lkml.org 
[lkml]   [2015]   [Mar]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 3/6] Documentation: DT: Document twl4030-madc-battery bindings
* Dr. H. Nikolaus Schaller <hns@goldelico.com> [150311 10:13]:
> Am 11.03.2015 um 17:44 schrieb Tony Lindgren <tony@atomide.com>:
> > * Dr. H. Nikolaus Schaller <hns@goldelico.com> [150311 09:17]:
> >> Am 11.03.2015 um 16:24 schrieb Tony Lindgren <tony@atomide.com>:
> >>>
> >>> Rather than just making platform_data into device tree properties..
> >>>
> >>> Can't you hide the these custom properties behind the compatible flag?
> >>>
> >>> You can initialize that data in the driver based on the compatible
> >>> flag and the match data.
> >>>
> >>> This makes sense if you can group things to similar configurations.
> >>
> >> Maybe I have not completely understood your proposal.
> >>
> >> Do you mean to go back to have big parameter tables for each device/battery
> >> combination in the driver code and the compatible flag (e.g. compatible = “board17”)
> >> chooses the right data set for the charging map and channels?
> >
> > If you can somehow group them, then yes.
>
> I don’t see how to group them. Could you make a proposal?

Sorry no idea about that :) I though you may have some ideas based on
dealing with the driver.

> >> I thought this is what the DT was introduced for - to have the same driver
> >> code but adapt to different boards depending on hardware variations.
> >
> > Yeah but you also need to consider the issues related to introducing
> > new device tree properties. The device tree properties introduced
> > should be generic where possible.
>
> Yes, that was discussed for a while for this driver’s bindings leading to v4.
>
> Which ones do you think are not generic enough?

It seems maps is the only one then, assuming the cpacity-uah can be made
Linux generic.

> >> And batteries have very different characteristics and vary between devices…
> >
> > Right. Maybe that has been already agreed on to use capacity-uah for
> > batteries in general?
>
> Ah, do you mean with generic/not generic the distinction between a “ti,” prefix
> and no prefix?
>
> Well, I don’t know if there is such an agreement and I would have no argument
> against calling it “ti,capacity-uah”.

No no, "capacity-uah" is what we should use, but you need an ack from
the battery and device tree people that this is OK. Let's not add
"ti,capacity-uah” as that can obviously be a generic property.

> > In that case I have not problem with that as
> > it’s a generic property :)
>
> Well, many batteries and systems have a fuel gauge chip (e.g. bq27000). This
> chip “knows” the capacity. But therefore it is not needed to specify
> it anywhere because it can be read out (usually in uAh).
>
> This driver is to solve the issue that there is no such factory-programmed
> battery or fuel gauge chip connected to a twl4030 driver. Nobody can program
> that capacity value - except someone matching the device tree with real hardware.
>
> And, by doing and averaging some charge-discharge cycles the fuel gauge
> mapping is calibrated.

OK

> >> The charging maps are depending on the battery type connected to the twl4030
> >> and which madc channel is which value is also a little hardware dependent
> >> (although the twl4030 doesn’t give much choice).
> >
> > Just to consider alternatives before introducing driver specific
> > property for the maps.. Maybe here you could have few different type
> > of maps and select something safe by default? Of course it could be this
> > is higly board specific, I think some devices may be able to run below
> > 3.3V for example..
>
> Every battery setup has a different map (which also might depend on the
> series resistance of the battery and the wiring).
>
> >
> >> And moving this information into the driver for each board that uses it
> >> would blow up the code.
> >
> > Right, I'm not saying we should build databases into the kernel drivers.
> > Just trying to avoid introducing driver specific properties unless
> > really needed :)
>
> They are not really driver specific, they are battery specific. They
> describe properties of the battery:
>
> * capacity - depends on battery
> * voltage depending on current charging level - depends on battery (and differs between charging and discharging)
> * wiring of MADC inputs to the twl4030 is board dependent.
>
> So all these properties are not driver specific, but describe hardware.
> And therefore they had been introduced exactly this way into the old
> platform_data driver.
>
> So if you want to see a “ti," prefix to the capacity property I would be
> fine.

Oh if they are battery spicific, then ideally we'd have generic batery
voltage to capacity maps property rather than a custom ti specific
property.

To avoid extra hassles later on, maybe you could submit a generic
binding patch only documenting it to the battery people and the device
tree people? That will make it easier to maintain this driver in the
long run.

Regards,

Tony


\
 
 \ /
  Last update: 2015-03-11 19:01    [W:0.093 / U:0.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site