lkml.org 
[lkml]   [2015]   [Feb]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subjectgxt4500 on x86 (Fire GL2)
Date
Hello,
I'm trying to get gxt4500 driver to work on x86 with Diamond/ATI Fire GL2 AGP
card:
01:00.0 VGA compatible controller [0300]: IBM GXT6000P Graphics Adapter [1014:0170] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Diamond Multimedia Systems Fire GL2 [1092:0172]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B+ DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f0000000 (32-bit, non-prefetchable) [size=64M]
[virtual] Expansion ROM at 30000000 [disabled] [size=256K]
Capabilities: [60] Power Management version 0
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x1
Kernel driver in use: gxt4500

After patching Kconfig, the driver compiled but does not work - monitor shows
no signal after driver load. Realized that PPC is big-endian while x86 is
little-endian and there are no endian conversions in the driver so did this:

--- a/drivers/video/fbdev/gxt4500.c
+++ b/drivers/video/fbdev/gxt4500.c
@@ -137,8 +137,8 @@ static const unsigned char watfmt[] = {
/* Colormap array; 1k entries of 4 bytes each */
#define CMAP 0x6000

-#define readreg(par, reg) readl((par)->regs + (reg))
-#define writereg(par, reg, val) writel((val), (par)->regs + (reg))
+#define readreg(par, reg) be32_to_cpu(readl((par)->regs + (reg)))
+#define writereg(par, reg, val) writel(cpu_to_be32(val), (par)->regs + (reg))

struct gxt4500_par {
void __iomem *regs;

But nothing changed, still no signal. Any ideas?

I was able to get the ancient fgl23 driver (from AMD web site) to work by
installing Debian Woody to a small partition. It's not very useful today but
it might be possible to dump the chip's registers and compare with gxt4500.

--
Ondrej Zary


\
 
 \ /
  Last update: 2015-02-12 22:21    [W:0.091 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site