lkml.org 
[lkml]   [2015]   [Feb]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 6/8] usb: dwc3: add ULPI interface support
Hi Heikki,

On Fri, Jan 23, 2015 at 05:12:56PM +0200, Heikki Krogerus wrote:
> Registers DWC3's ULPI interface with the ULPI bus when it's
> available.
>
> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
> ---
> drivers/usb/dwc3/Kconfig | 7 +++
> drivers/usb/dwc3/Makefile | 4 ++
> drivers/usb/dwc3/core.c | 6 +++
> drivers/usb/dwc3/core.h | 13 ++++++
> drivers/usb/dwc3/ulpi.c | 112 ++++++++++++++++++++++++++++++++++++++++++++++
> 5 files changed, 142 insertions(+)
> create mode 100644 drivers/usb/dwc3/ulpi.c
>
> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> index 58b5b2c..cda82ad 100644
> --- a/drivers/usb/dwc3/Kconfig
> +++ b/drivers/usb/dwc3/Kconfig
> @@ -11,6 +11,13 @@ config USB_DWC3
>
> if USB_DWC3
>
> +config USB_DWC3_ULPI
> + bool "Register ULPI PHY Interface"
> + depends on USB_ULPI_BUS=y
> + help
> + Select this if you have ULPI type PHY attached to your DWC3
> + controller.
> +
> choice
> bool "DWC3 Mode Selection"
> default USB_DWC3_DUAL_ROLE if (USB && USB_GADGET)
> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> index bb34fbc..2fc44e0 100644
> --- a/drivers/usb/dwc3/Makefile
> +++ b/drivers/usb/dwc3/Makefile
> @@ -16,6 +16,10 @@ ifneq ($(filter y,$(CONFIG_USB_DWC3_GADGET) $(CONFIG_USB_DWC3_DUAL_ROLE)),)
> dwc3-y += gadget.o ep0.o
> endif
>
> +ifneq ($(CONFIG_USB_DWC3_ULPI),)
> + dwc3-y += ulpi.o
> +endif
> +
> ifneq ($(CONFIG_DEBUG_FS),)
> dwc3-y += debugfs.o
> endif
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index a8c9062..66cbf38 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -879,6 +879,10 @@ static int dwc3_probe(struct platform_device *pdev)
> platform_set_drvdata(pdev, dwc);
> dwc3_cache_hwparams(dwc);
>
> + ret = dwc3_ulpi_init(dwc);

If I understood correctly, this call will result in enumerating the phy
via ULPI bus, then registering the correct ULPI device.
Can you guarantee ULPI will be always accessible at this point if we
remove dwc3 module and load it again?

Br, David


\
 
 \ /
  Last update: 2015-02-11 20:41    [W:0.292 / U:5.828 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site