lkml.org 
[lkml]   [2015]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH linux-next 1/2] irqchip: Add brcm,bcm6345-l1-intc device tree binding
Date
Add device tree binding for the BCM6345 interrupt controller.

This controller is similar to the SMP-capable BCM7038 and
the BCM3380 but with packed interrupt registers.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
---
Corrected example device name to be "interrupt-controller".

.../interrupt-controller/brcm,bcm6345-l1-intc.txt | 57 ++++++++++++++++++++++
1 file changed, 57 insertions(+)
create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt

diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt
new file mode 100644
index 0000000..4040905
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt
@@ -0,0 +1,57 @@
+Broadcom BCM6345-style Level 1 interrupt controller
+
+This block is a first level interrupt controller that is typically connected
+directly to one of the HW INT lines on each CPU.
+
+Key elements of the hardware design include:
+
+- 32, 64 or 128 incoming level IRQ lines
+
+- Most onchip peripherals are wired directly to an L1 input
+
+- A separate instance of the register set for each CPU, allowing individual
+ peripheral IRQs to be routed to any CPU
+
+- Contains one or more enable/status word pairs per CPU
+
+- No atomic set/clear operations
+
+- No polarity/level/edge settings
+
+- No FIFO or priority encoder logic; software is expected to read all
+ 2-4 status words to determine which IRQs are pending
+
+Required properties:
+
+- compatible: should be "brcm,bcm<soc>-l1-intc", "brcm,bcm6345-l1-intc"
+- reg: specifies the base physical address and size of the registers;
+ the number of supported IRQs is inferred from the size argument
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+ source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
+ this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+ node; valid values depend on the type of parent interrupt controller
+
+If multiple reg ranges and interrupt-parent entries are present on an SMP
+system, the driver will allow IRQ SMP affinity to be set up through the
+/proc/irq/ interface. In the simplest possible configuration, only one
+reg range and one interrupt-parent is needed.
+
+The driver operates in native CPU endian by default, there is no support for
+specifying an alternative endianness.
+
+Example:
+
+periph_intc: interrupt-controller@10000000 {
+ compatible = "brcm,bcm63168-l1-intc", "brcm,bcm6345-l1-intc";
+ reg = <0x10000020 0x20>,
+ <0x10000040 0x20>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&cpu_intc>;
+ interrupts = <2>, <3>;
+};
--
2.1.4
--
Simon Arlott


\
 
 \ /
  Last update: 2015-12-09 22:01    [W:0.049 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site