lkml.org 
[lkml]   [2015]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 13/19] ARM: dts: Add bus nodes using VDD_MIF for Exynos4x12
On 2015년 12월 10일 12:17, Krzysztof Kozlowski wrote:
> On 09.12.2015 13:08, Chanwoo Choi wrote:
>> This patch adds the bus noes using VDD_MIF for Exynos4x12 SoC.
>
> s/noes/nodes/

OK.

>
>> Exynos4x12 has the following AXI buses to translate data
>> between DRAM and DMC/ACP/C2C.
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> ---
>> arch/arm/boot/dts/exynos4x12.dtsi | 72 +++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 72 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
>> index b77dac61ffb5..3bcf0939755e 100644
>> --- a/arch/arm/boot/dts/exynos4x12.dtsi
>> +++ b/arch/arm/boot/dts/exynos4x12.dtsi
>> @@ -282,6 +282,78 @@
>> clocks = <&clock CLK_SMMU_LITE1>, <&clock CLK_FIMC_LITE1>;
>> #iommu-cells = <0>;
>> };
>> +
>> + bus_dmc: bus_dmc {
>> + compatible = "samsung,exynos-bus";
>> + clocks = <&clock CLK_DIV_DMC>;
>> + clock-names = "bus";
>> + operating-points-v2 = <&bus_dmc_opp_table>;
>> + status = "disabled";
>> + };
>> +
>> + bus_acp: bus_acp {
>> + compatible = "samsung,exynos-bus";
>> + clocks = <&clock CLK_DIV_ACP>;
>> + clock-names = "bus";
>> + operating-points-v2 = <&bus_acp_opp_table>;
>> + status = "disabled";
>> + };
>> +
>> + bus_c2c: bus_c2c {
>> + compatible = "samsung,exynos-bus";
>> + clocks = <&clock CLK_DIV_C2C>;
>> + clock-names = "bus";
>> + operating-points-v2 = <&bus_dmc_opp_table>;
>> + status = "disabled";
>> + };
>> +
>> + bus_dmc_opp_table: opp_table1 {
>> + compatible = "operating-points-v2";
>> + opp-shared;
>> +
>> + opp00 {
>> + opp-hz = /bits/ 64 <100000000>;
>> + opp-microvolt = <900000>;
>> + };
>> + opp01 {
>> + opp-hz = /bits/ 64 <134000000>;
>> + opp-microvolt = <900000>;
>> + };
>> + opp02 {
>> + opp-hz = /bits/ 64 <160000000>;
>> + opp-microvolt = <900000>;
>> + };
>> + opp03 {
>> + opp-hz = /bits/ 64 <200000000>;
>> + opp-microvolt = <950000>;
>
> The exyno4_bus.c (from mainline) uses 267 MHz here. Why choosing 200 MHz?

There is no special reason.
I'll change it (200MHz -> 267MHz).

Best Regards,
Chanwoo Choi



\
 
 \ /
  Last update: 2015-12-10 05:41    [W:0.328 / U:0.592 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site