lkml.org 
[lkml]   [2015]   [Dec]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3] extcon: add Maxim MAX3355 driver
Hi,

On 2015년 12월 17일 11:16, Chanwoo Choi wrote:
> Hi Sergei,
>
> On 2015년 12월 17일 03:07, Sergei Shtylyov wrote:
>> Maxim Integrated MAX3355E chip integrates a charge pump and comparators to
>> enable a system with an integrated USB OTG dual-role transceiver to
>> function as an USB OTG dual-role device. In addition to sensing/controlling
>> Vbus, the chip also passes thru the ID signal from the USB OTG connector.
>> On some Renesas boards, this signal is just fed into the SoC thru a GPIO
>> pin -- there's no real OTG controller, only host and gadget USB controllers
>> sharing the same USB bus; however, we'd like to allow host or gadget
>> drivers to be loaded depending on the cable type, hence the need for the
>> MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs
>> (however, we aren't currently interested in them), the OFFVBUS# signal is
>> controlled by the host controllers, there's also the SHDN# signal wired to
>> a GPIO, it should be driven high for the normal operation.
>>
>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
>>
>> ---
>> Changes in version 3:
>> - reformatted the change log.
>>
>> Changes in version 2:
>> - added the USB gadget cable support;
>> - added the remove() driver method which drives SHDN# GPIO low to save power;
>> - dropped vendor prefix from the ID GPIO property name;
>> - changed the GPIO property name suffix to "-gpios";
>> - switched to usign extcon_set_cable_state_() API;
>> - switched to using the gpiod/sleeping 'gpiolib' APIs;
>> - addded error messages to max3355_probe();
>> - added IRQF_NO_SUSPEND flasg to the devm_request_threaded_irq() call;
>> - renamed 'ret' variable to 'err' in max3355_probe();
>> - expanded the Kconfig entry help text;
>> - added vendor name to the patch summary, the bindings document, the Kconfig
>> entry, the driver heading comment, the module description, and the change log;
>> - fixed up and reformatted the change log.
>>
>> Documentation/devicetree/bindings/extcon/extcon-max3355.txt | 21 +
>> drivers/extcon/Kconfig | 8
>> drivers/extcon/Makefile | 1
>> drivers/extcon/extcon-max3355.c | 153 ++++++++++++
>> 4 files changed, 183 insertions(+)
>>

[snip]

>> + return 0;
>> +}
>> +
>> +static int max3355_remove(struct platform_device *pdev)
>> +{
>> + struct max3355_data *data = platform_get_drvdata(pdev);
>> +
>> + gpiod_set_value_cansleep(data->shdn_gpiod, 0);

Don't need to handle the 'shdn' gpio on resume/suspend funtcion?

But, if the interrput of id gpio is used for wakeup source,
there is no reason to handle it for suspend mode.

[snip]

Thanks,
Chanwoo Choi


\
 
 \ /
  Last update: 2015-12-17 04:01    [W:0.106 / U:1.616 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site