lkml.org 
[lkml]   [2015]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v6 1/4] drm: arm: Add DT bindings documentation for HDLCD driver.
Date
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/display/arm,hdlcd.txt | 79 ++++++++++++++++++++++
1 file changed, 79 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/arm,hdlcd.txt

diff --git a/Documentation/devicetree/bindings/display/arm,hdlcd.txt b/Documentation/devicetree/bindings/display/arm,hdlcd.txt
new file mode 100644
index 0000000..78bc242
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/arm,hdlcd.txt
@@ -0,0 +1,79 @@
+ARM HDLCD
+
+This is a display controller found on several development platforms produced
+by ARM Ltd and in more modern of its' Fast Models. The HDLCD is an RGB
+streamer that reads the data from a framebuffer and sends it to a single
+digital encoder (DVI or HDMI).
+
+Required properties:
+ - compatible: "arm,hdlcd"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: One interrupt used by the display controller to notify the
+ interrupt controller when any of the interrupt sources programmed in
+ the interrupt mask register have activated.
+ - clocks: A list of phandle + clock-specifier pairs, one for each
+ entry in 'clock-names'.
+ - clock-names: A list of clock names. For HDLCD it should contain:
+ - "pxlclk" for the clock feeding the output PLL of the controller.
+
+Required sub-nodes:
+ - port: The HDLCD connection to an encoder chip. The connection is modeled
+ using the OF graph bindings specified in
+ Documentation/devicetree/bindings/graph.txt.
+
+Optional properties:
+ - memory-region: phandle to a node describing memory (see
+ Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) to be
+ used for the framebuffer; if not present, the framebuffer may be located
+ anywhere in memory.
+
+
+Example:
+
+/ {
+ ...
+
+ hdlcd@2b000000 {
+ compatible = "arm,hdlcd";
+ reg = <0 0x2b000000 0 0x1000>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&oscclk5>;
+ clock-names = "pxlclk";
+ port {
+ hdlcd_output: endpoint@0 {
+ remote-endpoint = <&hdmi_enc_input>;
+ };
+ };
+ };
+
+ /* HDMI encoder on I2C bus */
+ i2c@7ffa0000 {
+ ....
+ hdmi-transmitter@70 {
+ compatible = ".....";
+ reg = <0x70>;
+ port@0 {
+ hdmi_enc_input: endpoint {
+ remote-endpoint = <&hdlcd_output>;
+ };
+
+ hdmi_enc_output: endpoint {
+ remote-endpoint = <&hdmi_1_port>;
+ };
+ };
+ };
+
+ };
+
+ hdmi1: connector@1 {
+ compatible = "hdmi-connector";
+ type = "a";
+ port {
+ hdmi_1_port: endpoint {
+ remote-endpoint = <&hdmi_enc_output>;
+ };
+ };
+ };
+
+ ...
+};
--
2.6.4


\
 
 \ /
  Last update: 2015-12-11 16:21    [W:0.039 / U:5.632 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site