lkml.org 
[lkml]   [2015]   [Dec]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: LM90 driver and ti tmp461 detection
On Thu, Dec 10, 2015 at 08:41:57AM -0800, Guenter Roeck wrote:
> On 12/10/2015 04:08 AM, Andreas Werner wrote:
> >Hi,
> >i have a temperature sensor device named "TI TMP461" which is quite the
> >same than the tmp451 which is already included in the lm90 driver.
> >
> >I just want to add the tmp461 to the driver but currently i have no way
> >to differ between the tmp461 and tmp451.
> >
> >The main different is that the tmp461 address can be configured by to Pins
> >whereas the tmp451 has a fixed address.
> >
> >The register layout is quite the same except that the tmp461 has one
> >register more (0x16 Channel Enable Register).
> >
> >Every zero bit is the same for both bits, so we cannot use these bits for
> >identification.
> >
> >Does anybody of you have a tmp451 to read out the register 0x16 (which is
> >not implement but i expect a value). May be we can use this to
> >identify the tmp461.
> >
>
> Here is a register dump.
>
> 00: 5d 69 00 04 08 bf 00 ff 53 00 00 00 00 00 00 00 ]i.???..S.......
> 10: a0 00 00 00 00 f0 00 00 00 a9 00 00 00 00 00 00 ?....?...?......
> 20: b8 0a 01 00 00 XX 00 00 00 00 0e 00 00 00 00 00 ???..X....?.....
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 00 ..............U.
>
> there is nothing to distinguish the two chips as far as I can see.
> Is your system a devicetree system ? If so, you can just
> provide a compatible statement such as
> compatible = "ti,tmp461", "ti,tmp451";
> or simply instantiate the chip as tmp451.
>
> Feel free to provide a patch adding '{ "tmp461", tmp451 },'
> to lm90_id as well as the necessary documentation, but I don't
> think there is anything we can do to detect the chip.
>
> On the other side, I am a bit concerned that the chip detection doesn't
> work well, since the chip ID register is really unsupported and just happens
> to return 0 for both chips. I wonder if there are other TI chips which may
> be mis-detected as TMP451.
>
> Thanks,
> Guenter
>

Hi,
thanks for the register dump :-)

There is one difference. The temperature ranges differ:

TMP451:
Standard Mode: 0 to +127
Extended Mode: -64 to +191

TMP461:
Standard Mode: -40 to +127
Extended Mode: -64 to +191

Therefore the calcualtion is different then the tmp451 one.

I also aggree with you with the magical ID register. I hate such
kind of register with are not documented and may have a value.

I have a DT based board yes, but i have also planed to submit my changes
and also wanted to implement the autodetection of the chip.

I have also planned (or need) to implement the "n-Factor Correction" for the
CPU diodes. There is a register to set this value in the tmp451 and tmp461.
Would that make sense to add a DT property for the driver to be able
to set this value? What do you think?

Regards
Andy


\
 
 \ /
  Last update: 2015-12-10 19:01    [W:0.139 / U:0.500 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site