lkml.org 
[lkml]   [2015]   [Nov]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] mmc: core: fix __mmc_switch timeout caused by preempt
Date
there is a time window between __mmc_send_status() and time_afer(),
on some eMMC chip, the timeout_ms is only 10ms, if this thread was
scheduled out during this period, then, even card has already changes
to transfer state by the result of CMD13, this part of code also treat
it to timeout error.
So, need calculate timeout first, then call __mmc_send_status(), if
already timeout and card still in programing state, then treat it to
the real timeout error.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
drivers/mmc/core/mmc_ops.c | 23 ++++++++++++++---------
1 file changed, 14 insertions(+), 9 deletions(-)

diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
index 1f44426..0add634 100644
--- a/drivers/mmc/core/mmc_ops.c
+++ b/drivers/mmc/core/mmc_ops.c
@@ -489,6 +489,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
unsigned long timeout;
u32 status = 0;
bool use_r1b_resp = use_busy_signal;
+ bool expired = false;

mmc_retune_hold(host);

@@ -544,10 +545,22 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
/* Must check status to be sure of no errors. */
timeout = jiffies + msecs_to_jiffies(timeout_ms);
do {
+ /* Timeout if the device never leaves the program state.
+ * must check it firstly to avoid problem caused by preempt.
+ */
+ expired = time_after(jiffies, timeout);
+
if (send_status) {
err = __mmc_send_status(card, &status, ignore_crc);
- if (err)
+ if (err) {
goto out;
+ } else if (expired &&
+ R1_CURRENT_STATE(status) == R1_STATE_PRG) {
+ pr_err("%s: Card stuck in programming state! %s\n",
+ mmc_hostname(host), __func__);
+ err = -ETIMEDOUT;
+ goto out;
+ }
}
if ((host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp)
break;
@@ -563,14 +576,6 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
mmc_delay(timeout_ms);
goto out;
}
-
- /* Timeout if the device never leaves the program state. */
- if (time_after(jiffies, timeout)) {
- pr_err("%s: Card stuck in programming state! %s\n",
- mmc_hostname(host), __func__);
- err = -ETIMEDOUT;
- goto out;
- }
} while (R1_CURRENT_STATE(status) == R1_STATE_PRG);

err = mmc_switch_status_error(host, status);
--
1.8.1.1.dirty


\
 
 \ /
  Last update: 2015-11-26 04:01    [W:0.037 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site