lkml.org 
[lkml]   [2015]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 6/6] net: dsa: mv88e6060: replace magic values with register defines
Date
To align with the mv88e6xxx code, use the register defines to
access all the register addresses and bit fields.

Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/net/dsa/mv88e6060.c | 64 ++++++++++++++++++++++++++-------------------
1 file changed, 37 insertions(+), 27 deletions(-)

diff --git a/drivers/net/dsa/mv88e6060.c b/drivers/net/dsa/mv88e6060.c
index cd08079..0527f48 100644
--- a/drivers/net/dsa/mv88e6060.c
+++ b/drivers/net/dsa/mv88e6060.c
@@ -15,9 +15,7 @@
#include <linux/netdevice.h>
#include <linux/phy.h>
#include <net/dsa.h>
-
-#define REG_PORT(p) (8 + (p))
-#define REG_GLOBAL 0x0f
+#include "mv88e6060.h"

static int reg_read(struct dsa_switch *ds, int addr, int reg)
{
@@ -67,13 +65,14 @@ static char *mv88e6060_probe(struct device *host_dev, int sw_addr)
if (bus == NULL)
return NULL;

- ret = mdiobus_read(bus, sw_addr + REG_PORT(0), 0x03);
+ ret = mdiobus_read(bus, sw_addr + REG_PORT(0), PORT_SWITCH_ID);
if (ret >= 0) {
- if (ret == 0x0600)
+ if (ret == PORT_SWITCH_ID_6060)
return "Marvell 88E6060 (A0)";
- if (ret == 0x0601 || ret == 0x0602)
+ if (ret == PORT_SWITCH_ID_6060_R1 ||
+ ret == PORT_SWITCH_ID_6060_R2)
return "Marvell 88E6060 (B0)";
- if ((ret & 0xfff0) == 0x0600)
+ if ((ret & PORT_SWITCH_ID_6060_MASK) == PORT_SWITCH_ID_6060)
return "Marvell 88E6060";
}

@@ -87,22 +86,26 @@ static int mv88e6060_switch_reset(struct dsa_switch *ds)
unsigned long timeout;

/* Set all ports to the disabled state. */
- for (i = 0; i < 6; i++) {
- ret = REG_READ(REG_PORT(i), 0x04);
- REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
+ for (i = 0; i < MV88E6060_PORTS; i++) {
+ ret = REG_READ(REG_PORT(i), PORT_CONTROL);
+ REG_WRITE(REG_PORT(i), PORT_CONTROL,
+ ret & ~PORT_CONTROL_STATE_MASK);
}

/* Wait for transmit queues to drain. */
usleep_range(2000, 4000);

/* Reset the switch. */
- REG_WRITE(REG_GLOBAL, 0x0a, 0xa130);
+ REG_WRITE(REG_GLOBAL, GLOBAL_ATU_CONTROL,
+ GLOBAL_ATU_CONTROL_SWRESET |
+ GLOBAL_ATU_CONTROL_ATUSIZE_1024 |
+ GLOBAL_ATU_CONTROL_ATE_AGE_5MIN);

/* Wait up to one second for reset to complete. */
timeout = jiffies + 1 * HZ;
while (time_before(jiffies, timeout)) {
- ret = REG_READ(REG_GLOBAL, 0x00);
- if (ret & 0x800)
+ ret = REG_READ(REG_GLOBAL, GLOBAL_STATUS);
+ if (ret & GLOBAL_STATUS_INIT_READY)
break;

usleep_range(1000, 2000);
@@ -119,13 +122,15 @@ static int mv88e6060_setup_global(struct dsa_switch *ds)
* set the maximum frame size to 1536 bytes, and mask all
* interrupt sources.
*/
- REG_WRITE(REG_GLOBAL, 0x04, 0x400);
+ REG_WRITE(REG_GLOBAL, GLOBAL_CONTROL, GLOBAL_CONTROL_MAX_FRAME_1536);

/* Enable automatic address learning, set the address
* database size to 1024 entries, and set the default aging
* time to 5 minutes.
*/
- REG_WRITE(REG_GLOBAL, 0x0a, 0x2130);
+ REG_WRITE(REG_GLOBAL, GLOBAL_ATU_CONTROL,
+ GLOBAL_ATU_CONTROL_ATUSIZE_1024 |
+ GLOBAL_ATU_CONTROL_ATE_AGE_5MIN);

return 0;
}
@@ -139,25 +144,30 @@ static int mv88e6060_setup_port(struct dsa_switch *ds, int p)
* state to Forwarding. Additionally, if this is the CPU
* port, enable Ingress and Egress Trailer tagging mode.
*/
- REG_WRITE(addr, 0x04, dsa_is_cpu_port(ds, p) ? 0x4103 : 0x0003);
+ REG_WRITE(addr, PORT_CONTROL,
+ dsa_is_cpu_port(ds, p) ?
+ PORT_CONTROL_TRAILER |
+ PORT_CONTROL_INGRESS_MODE |
+ PORT_CONTROL_STATE_FORWARDING :
+ PORT_CONTROL_STATE_FORWARDING);

/* Port based VLAN map: give each port its own address
* database, allow the CPU port to talk to each of the 'real'
* ports, and allow each of the 'real' ports to only talk to
* the CPU port.
*/
- REG_WRITE(addr, 0x06,
- ((p & 0xf) << 12) |
- (dsa_is_cpu_port(ds, p) ?
- ds->phys_port_mask :
- (1 << ds->dst->cpu_port)));
+ REG_WRITE(addr, PORT_VLAN_MAP,
+ ((p & 0xf) << PORT_VLAN_MAP_DBNUM_SHIFT) |
+ (dsa_is_cpu_port(ds, p) ?
+ ds->phys_port_mask :
+ BIT(ds->dst->cpu_port)));

/* Port Association Vector: when learning source addresses
* of packets, add the address to the address database using
* a port bitmap that has only the bit for this port set and
* the other bits clear.
*/
- REG_WRITE(addr, 0x0b, 1 << p);
+ REG_WRITE(addr, PORT_ASSOC_VECTOR, BIT(p));

return 0;
}
@@ -177,7 +187,7 @@ static int mv88e6060_setup(struct dsa_switch *ds)
if (ret < 0)
return ret;

- for (i = 0; i < 6; i++) {
+ for (i = 0; i < MV88E6060_PORTS; i++) {
ret = mv88e6060_setup_port(ds, i);
if (ret < 0)
return ret;
@@ -189,16 +199,16 @@ static int mv88e6060_setup(struct dsa_switch *ds)
static int mv88e6060_set_addr(struct dsa_switch *ds, u8 *addr)
{
/* Use the same MAC Address as FD Pause frames for all ports */
- REG_WRITE(REG_GLOBAL, 0x01, (addr[0] << 9) | addr[1]);
- REG_WRITE(REG_GLOBAL, 0x02, (addr[2] << 8) | addr[3]);
- REG_WRITE(REG_GLOBAL, 0x03, (addr[4] << 8) | addr[5]);
+ REG_WRITE(REG_GLOBAL, GLOBAL_MAC_01, (addr[0] << 9) | addr[1]);
+ REG_WRITE(REG_GLOBAL, GLOBAL_MAC_23, (addr[2] << 8) | addr[3]);
+ REG_WRITE(REG_GLOBAL, GLOBAL_MAC_45, (addr[4] << 8) | addr[5]);

return 0;
}

static int mv88e6060_port_to_phy_addr(int port)
{
- if (port >= 0 && port <= 5)
+ if (port >= 0 && port < MV88E6060_PORTS)
return port;
return -1;
}
--
1.9.1

\
 
 \ /
  Last update: 2015-11-10 17:01    [W:0.043 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site