lkml.org 
[lkml]   [2015]   [Oct]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 10/10] pwm: sunxi: Add possibility to pulse the sunxi pwm output
Date
From: Olliver Schinagl <oliver@schinagl.nl>

With the new pulse mode addition to the PWM framework, we can make use
of this for the sunxi PWM.

WARNING: Do not merge yet, currently, we can only pulse once and a
manual disable is required to 'reset' the PWM framework. I haven't
thought through how to automatically 'disable' the PWM after the pulse
is finished and need some guidance here.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
---
drivers/pwm/pwm-sun4i.c | 14 +++++++++++---
1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
index 6347ca8..8370cca 100644
--- a/drivers/pwm/pwm-sun4i.c
+++ b/drivers/pwm/pwm-sun4i.c
@@ -32,7 +32,7 @@
#define PWM_EN BIT(4)
#define PWM_ACT_STATE BIT(5)
#define PWM_CLK_GATING BIT(6)
-#define PWM_MODE BIT(7)
+#define PWM_MODE_PULSE BIT(7)
#define PWM_PULSE BIT(8)
#define PWM_BYPASS BIT(9)

@@ -166,6 +166,8 @@ static int sun4i_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,

spin_lock(&sun4i_pwm->ctrl_lock);
val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
+ if (pulse_count)
+ val |= BIT_CH(PWM_MODE_PULSE, pwm->hwpwm);
if (sun4i_pwm->data->has_rdy && (val & PWM_RDY(pwm->hwpwm))) {
ret = -EBUSY;
goto out;
@@ -237,7 +239,10 @@ static int sun4i_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)

spin_lock(&sun4i_pwm->ctrl_lock);
val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
- val |= BIT_CH(PWM_EN, pwm->hwpwm);
+ if (pwm->pulse_count)
+ val |= BIT_CH(PWM_PULSE, pwm->hwpwm);
+ else
+ val |= BIT_CH(PWM_EN, pwm->hwpwm);
val |= BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
sun4i_pwm_writel(sun4i_pwm, val, PWM_CTRL_REG);
spin_unlock(&sun4i_pwm->ctrl_lock);
@@ -350,9 +355,12 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
}

val = sun4i_pwm_readl(pwm, PWM_CTRL_REG);
- for (i = 0; i < pwm->chip.npwm; i++)
+ for (i = 0; i < pwm->chip.npwm; i++) {
if (!(val & BIT_CH(PWM_ACT_STATE, i)))
pwm->chip.pwms[i].polarity = PWM_POLARITY_INVERSED;
+
+ pwm_set_pulse_count_max(&pwm->chip.pwms[i], 1);
+ }
clk_disable_unprepare(pwm->clk);

return 0;
--
2.6.1


\
 
 \ /
  Last update: 2015-10-26 23:01    [W:0.066 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site