lkml.org 
[lkml]   [2015]   [Oct]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] mmc: pwrseq: Use highest priority for eMMC restart handler
Hi Javier,

On 22 October 2015 at 14:06, Javier Martinez Canillas
<javier@osg.samsung.com> wrote:
> Hello Anand,
>
> On 10/22/2015 07:03 AM, Anand Moon wrote:
>> Hi Javier,
>>
>> On 22 October 2015 at 08:22, Javier Martinez Canillas
>> <javier@osg.samsung.com> wrote:
>>> Hello Krzysztof,
>>>
>>> On 10/22/2015 03:43 AM, Krzysztof Kozlowski wrote:
>>>> On 22.10.2015 10:20, Javier Martinez Canillas wrote:> Hello Krzysztof,
>>>>>
>>>>> Thanks for your feedback.
>>>>>
>>>>> On 10/22/2015 02:36 AM, Krzysztof Kozlowski wrote:
>>>>>> On 22.10.2015 00:15, Javier Martinez Canillas wrote:
>>>>>>> The pwrseq_emmc driver does a eMMC card reset before a system reboot to
>>>>>>> allow broken or limited ROM boot-loaders (that don't have an eMMC reset
>>>>>>> logic) to be able to read the second stage from the eMMC.
>>>>>>>
>>>>>>> But this has to be called before a system reboot handler and while most
>>>>>>> of them use the priority 128, there are other restart handlers (such as
>>>>>>> the syscon-reboot one) that use a higher priority. So, use the highest
>>>>>>> priority to make sure that the eMMC hw is reset before a system reboot.
>>>>>>>
>>>>>>> Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
>>>>>>> Tested-by: Markus Reichl <m.reichl@fivetechno.de>
>>>>>>> Tested-by: Anand Moon <linux.amoon@gmail.com>
>>>>>>> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
>>>>>>>
>>>>>>> ---
>>>>>>> Hello,
>>>>>>>
>>>>>>> This patch was needed since a recent series from Alim [0] added
>>>>>>> syscon reboot and poweroff support to Exynos SoCs and removed
>>>>>>> the reset handler in the Exynos Power Management Unit (PMU) code.
>>>>>>>
>>>>>>> But the PMU and syscon-reboot restart handler have a different
>>>>>>> priority so [0] breaks restart when eMMC is used on these boards.
>>>>>>>
>>>>>>> [0]: http://www.spinics.net/lists/arm-kernel/msg454396.html
>>>>>>>
>>>>>>> So this patch must be merged before [0] to avoid regressions.
>>>>>>>
>>>>>>> Best regards,
>>>>>>> Javier
>>>>>>>
>>>>>>> drivers/mmc/core/pwrseq_emmc.c | 6 +++---
>>>>>>> 1 file changed, 3 insertions(+), 3 deletions(-)
>>>>>>>
>>>>>>> diff --git a/drivers/mmc/core/pwrseq_emmc.c b/drivers/mmc/core/pwrseq_emmc.c
>>>>>>> index 137c97fb7aa8..ad4f94ec7e8d 100644
>>>>>>> --- a/drivers/mmc/core/pwrseq_emmc.c
>>>>>>> +++ b/drivers/mmc/core/pwrseq_emmc.c
>>>>>>> @@ -84,11 +84,11 @@ struct mmc_pwrseq *mmc_pwrseq_emmc_alloc(struct mmc_host *host,
>>>>>>>
>>>>>>> /*
>>>>>>> * register reset handler to ensure emmc reset also from
>>>>>>> - * emergency_reboot(), priority 129 schedules it just before
>>>>>>> - * system reboot
>>>>>>> + * emergency_reboot(), priority 255 is the highest priority
>>>>>>> + * so it will be executed before any system reboot handler.
>>>>>>> */
>>>>>>> pwrseq->reset_nb.notifier_call = mmc_pwrseq_emmc_reset_nb;
>>>>>>> - pwrseq->reset_nb.priority = 129;
>>>>>>> + pwrseq->reset_nb.priority = 255;
>>>>>>
>>>>>> I see the problem which you are trying to solve but this may be tricker
>>>>>> then just kicking the number. Some of restart handlers are registered
>>>>>> with priority 192. I found few of such, like: at91_restart_nb,
>>>>>> zynq_slcr_restart_nb, rmobile_reset_nb (maybe more, I did not grep too
>>>>>> much).
>>>>>>
>>>>>
>>>>> Yes, the syscon-reboot restart handler also uses a priority 192 and that
>>>>> is why reboot with eMMC broke with Alim's patches since the PMU restart
>>>>> handler priority is 128.
>>>>>
>>>>>> I guess they chose the "192" priority on purpose.
>>>>>>
>>>>>
>>>>> I tried to understand what's the policy w.r.t priority numbering for
>>>>> restart handlers but only found this in the register_restart_handler
>>>>> kernel-doc [0]:
>>>>>
>>>>> /**
>>>>> * register_restart_handler - Register function to be called to reset
>>>>> * the system
>>>>> * @nb: Info about handler function to be called
>>>>> * @nb->priority: Handler priority. Handlers should follow the
>>>>> * following guidelines for setting priorities.
>>>>> * 0: Restart handler of last resort,
>>>>> * with limited restart capabilities
>>>>> * 128: Default restart handler; use if no other
>>>>> * restart handler is expected to be available,
>>>>> * and/or if restart functionality is
>>>>> * sufficient to restart the entire system
>>>>> * 255: Highest priority restart handler, will
>>>>> * preempt all other restart handlers
>>>>>
>>>>> So, reading that is not clear to me if only the values 0, 128 and 255
>>>>> should be used or any value from 0-255.
>>>>>
>>>>> What's clear to me is that restart handlers to reset a specific hw block
>>>>> should be called before the restart handler that resets the whole system.
>>>>>
>>>>> The 192 seems to be used because there are other default restart handlers
>>>>> that are using a prio of 128. See for example the commit that changed the
>>>>> syscon-reboot prio from 128 to 192:
>>>>>
>>>>> b81180b3fd48 power: reset: adjust priority of simple syscon reboot driver
>>>>
>>>> But were are here not talking about syscon handler but the others. Now
>>>> you will be ahead of them.
>>>>
>>>
>>> Yes, I know that. My point was that the platforms were either not using the
>>> mmc-pwrseq-emmc or their system restart handler already had a lower priority
>>> but that is not true for at least rk3288-veyron as you said.
>>>
>>>>>
>>>>> So probably the 192 value was chosen because is in the middle of 128 and
>>>>> 255 but it seems to me a rather arbitrary value and I would prefer it to
>>>>> be documented in some place.
>>>>>
>>>>>> Effectively, now the emmc handler will be executed before their
>>>>>> handlers... is it an issue? Maybe some testing on these platforms is
>>>>>> necessary?
>>>>>>
>>>>>
>>>>> I don't think is an issue, the reason why I chose 255 is that it is
>>>>> a documented value in the kernel-doc and since is the highest prio,
>>>>> it makes sure the eMMC will be reset before any system restart handler.
>>>>>
>>>>> Also, the pwrseq_emmc driver is only used in platforms whose SoC ROM
>>>>> can either leave the eMMC in an unknown state so the kernel needs to
>>>>> hw reset the eMMC or does not have a reset logic so it can only read
>>>>> from an eMMC if is in a known state (i.e: after a reset from kernel).
>>>>
>>>> I think at least one platform may be affected because it used
>>>> mmc-pwrseq-emmc and gpio-restart.
>>>>
>>>> Look at rk3288-veyron.dtsi.
>>>>
>>>> Both of restart handlers had the priority of 129 which means that the
>>>> order of execution depends on probing sequence. Now you will make the
>>>> sequence strict - first mmc then gpio.
>>>>
>>>
>>> The behavior is going to change indeed in that board but no due probe
>>> order but because the gpio-restart handler dev node has priority = <200>
>>> which overrides the default 129 in the gpio-restart driver.
>>>
>>> So before $SUBJECT the eMMC restart handler was not executed but now it
>>> will be after this change.
>>>
>>>> You seems convinced that this is not a problem... I don't know. I would
>>>> prefer test this on affected platforms before risking to break them.
>>>> It's annoying if fix for one SoC breaks another.
>>>>
>>>
>>> Agreed.
>>>
>>>>>
>>>>> Since the current mmc_pwrseq_emmc_reset_nb notifier priority is 129,
>>>>> eMMC reset will not work if one of the platforms you mentioned needs
>>>>> this since the system restart handler with prio 192 will be executed
>>>>> before the eMMC one, leaving the eMMC in an unknown state on reboot.
>>>>
>>>> And now you will "fix this" by making eMMC working correctly. So let's
>>>> make it straight:
>>>> 1. Previously the eMMC could be left on these platforms in an unknown
>>>> state (because emmc handler was not executed).
>>>> 2. No one complained! Which could mean that in fact this was working fine...
>>>> 3. Now you will change it.
>>>> 4. Maybe someone will complain?
>>>>
>>>> Just test it (or get an ack/tested tag). That's all what is needed.
>>>>
>>>
>>> Yes, I never meant that the patch should be merged without testing...
>>>
>>>>
>>>>> And $SUBJECT should not cause any regressions for the platforms that
>>>>> are currently using the pwrseq_emmc, since the restart handler was
>>>>> already being called before the system restart handler so bumping
>>>>> the priority should not cause any effect.
>>>>
>>>> I found at least one platform where the sequence *might* change. There
>>>> could be more of them.
>>>>
>>>
>>> Agreed, I missed that rk3288-veyron is using a restart handler with higher
>>> priority and could be other boards too as you said.
>>>
>>> Let's see what is Marek's opinion since he added the pwrseq_emmc support
>>> and also what Ulf thinks about always doing a eMMC reset before reboot.
>>>
>>> I can't think how doing a eMMC card reset before reboot could affect a
>>> board but you are right that we don't know without testing.
>>>
>>>> Best regards,
>>>> Krzysztof
>>>>
>>>
>>
>> Well I have tested with
>>
>> pwrseq->reset_nb.priority = 192;
>>
>
> I'm not sure why you are testing that case to be honest.
>
>> But it did not resolve the issue of reboot.
>>
>
> That's expected since you are using the same priority for both
> the mmc-pwrseq-emmc and syscon-reboot restart handlers so it
> will only work if the eMMC restart handler is registered before
> the syscon one and I don't if that's the case.
>
> The eMMC restart handler priority should be higher than the one
> used by syscon-reboot (or any system restart handler) to work.
>
>> will early rest of emmc will that not affect the sync of data before reboot.
>>
>
> Is this a question? It shouldn't since the restart handlers are
> the last things that are executed before a system is rebooted.

Thanks, I got that before restart all the data will be sync,
All the mounted filesystem will get umounted.

-Anand Moon
>
>> -Anand Moon
>>
>
> Best regards,
> --
> Javier Martinez Canillas
> Open Source Group
> Samsung Research America


\
 
 \ /
  Last update: 2015-10-22 12:01    [W:3.383 / U:0.004 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site