lkml.org 
[lkml]   [2015]   [Oct]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [GIT PULL] On-demand device probing
On Tue, Oct 20, 2015 at 3:39 AM, Russell King - ARM Linux
<linux@arm.linux.org.uk> wrote:
> On Mon, Oct 19, 2015 at 08:27:44PM +0200, Uwe Kleine-König wrote:
>> Hello,
>>
>> On Mon, Oct 19, 2015 at 04:43:24PM +0100, Russell King - ARM Linux wrote:
>> > It's a bit ironic that you've chosen GPIO as an example there. The
>> > "new" GPIO API (the gpiod_* stuff) only has a fwnode way to get the
>> > gpio descriptor. There's no of_* method.
>>
>> Without following all that fwnode discussion:
>> gpiod_get et al. should work for you here, doesn't it? It just takes a
>> struct device * and I'm happy with it.
>
> What if you don't have a struct device? I had that problem recently
> when modifying the mvebu PCIe code. The 'struct device' node doesn't
> contain the GPIOs, it's the PCIe controller. Individual ports on the
> controller are described in DT as sub-nodes, and the sub-nodes can
> have a GPIO for card reset purposes. These sub-nodes don't have a
> struct device.
>
> Right now, I'm having to do this to work around this issue:
>
> reset_gpio = of_get_named_gpio_flags(child, "reset-gpios", 0, &flags);
> if (reset_gpio == -EPROBE_DEFER) {
> ret = reset_gpio;
> goto err;
> }
>
> if (gpio_is_valid(reset_gpio)) {
> unsigned long gpio_flags;
>
> port->reset_name = devm_kasprintf(dev, GFP_KERNEL, "%s-reset",
> port->name);
> if (!port->reset_name) {
> ret = -ENOMEM;
> goto err;
> }
>
> if (flags & OF_GPIO_ACTIVE_LOW) {
> dev_info(dev, "%s: reset gpio is active low\n",
> of_node_full_name(child));
> gpio_flags = GPIOF_ACTIVE_LOW |
> GPIOF_OUT_INIT_LOW;
> } else {
> gpio_flags = GPIOF_OUT_INIT_HIGH;
> }
>
> ret = devm_gpio_request_one(dev, reset_gpio, gpio_flags,
> port->reset_name);
> if (ret) {
> if (ret == -EPROBE_DEFER)
> goto err;
> goto skip;
> }
>
> port->reset_gpio = gpio_to_desc(reset_gpio);
> }
>
> Not nice, is it? Not nice to have that in lots of drivers either.
>
> However, switching to use any of_* or fwnode_* thing also carries with
> it another problem: you can't control the name appearing in the
> allocation, so you end up with a bunch of GPIOs requested with a "reset"
> name - meaning you lose any identification of which port the GPIO was
> bound to.

There are a few holes in the gpiod API. I see two solutions here:

1) extend devm_get_gpiod_from_child() to take an optional name argument
2) add a function to explicitly change a GPIO's name

2) seems to be the most generic solution, would that do the trick?

(sorry for the off-topic)


\
 
 \ /
  Last update: 2015-10-20 02:01    [W:0.572 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site