lkml.org 
[lkml]   [2015]   [Oct]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] PCI: IOV: read SRIOV_NUM_VF after enabling ARI
Hi Ben,

Thanks for the detailed response!

On Fri, Oct 16, 2015 at 11:56:28AM -0500, Ben Shelton wrote:
> Hi Bjorn,
>
> > What problem does this patch solve, Ben? I assume you have devices
> > that do change TotalVFs when ARI is enabled, and you do want the new
> > value?
> >
> > Or is the problem something like the following:
> >
> > - ...
> > - Linux PCI core sees TotalVFs = X (saved as iov->total_VFs)
> > - Linux sets ARI Capable Hierarchy
> > - Device changes TotalVFs to X + Y (but PCI core doesn't notice)
> > - Driver reads TotalVFs and sees X + Y
> > - Driver attempts pci_enable_sriov(dev, X + Y), which fails because
> > sriov_enable() sees "X + Y > iov->total_VFs"
>
> Here's a short snippet from the databook for the PCI Express controller we're
> using:
>
> "Supports two sets of VF Stride, First VF Offset, InitialVFs, and TotalVFs
> registers per PF—one each for ARI and non-ARI hierarchies. Selection is
> performed by host software through the ARI Capable Hierarchy bit of the Control
> register in the PF0 SR-IOV capability structure."
>
> The values in InitialVFs and TotalVFs are HWinit for each set of registers.

The HwInit description says "bits are read-only after initialization
and can only be reset (for write-once by firmware) with 'Power Good
Reset'." I don't see any provision for different values based on a
control register bit, so I think this device is actually out of spec.

We should be able to deal with it, so it's not that big a deal, but we
will have to keep it in mind and probably mention it in a comment in
the code.

> So the issue this is intended to fix is the following:
>
> - Linux PCI core sees TotalVFs = X (saved as iov->total_VFs).
> - Linux sets ARI Capable Hierarchy.
> - Device switches to exposing the second set of registers, where
> InitialVFs = TotalVFs = Y (where Y > X).
> - User enables one or more VFs on the device, e.g. by writing a value to
> sriov_numvfs in the sysfs.
> - Driver calls pci_enable_sriov() for the device, which then calls
> sriov_enable(). sriov_enable() reads InitialVFs (= Y) and then checks if it's
> greater than iov->total_VFs (= X). Since Y > X, the comparison is true, so
> sriov_enable() fails out and returns -EIO.

I think there are two problems here:

1) We should be reading some registers together to make sure we get
consistent values. For example, we always read VFOffset and
VFStride immediately after writing NumVFs. I think we should
read InitialVFs and TotalVFs together. I don't see the point of
reading TotalVFs in sriov_init() and reading InitialVFs in
sriov_enable(). If we read them both in sriov_init(), I don't
think we'd have this problem of sriov_enable() returning -EIO.

2) To work around this non-compliant device, we should read InitialVFs
and TotalVFs after setting the ARI bit.

Ideally, I think this would be two patches: one to move the InitialVFs
read from sriov_enable() to sriov_init(), and a second to move the
pair from before setting ARI to after.

> > I'm a little dubious about drivers reading the SRIOV capability
> > directly, so maybe this is a symptom of deeper problems.
>
> I agree that the driver should not be reading the capability directly, but from
> what I understand, it's intended for the device itself to do this. From the PCI
> SR-IOV spec revision 1.1:
>
> "ARI Capable Hierarchy is a hint to the Device that ARI has been enabled in the
> Root Port or Switch Downstream Port immediately above the Device."

Sure, of course, the device should behave differently based on how the
registers are programmed; that's the whole point of having writable
registers. I think the particular case of the device changing HwInit
registers is out of spec, but changing things like VFOffset and
VFStride is completely expected.

Bjorn


\
 
 \ /
  Last update: 2015-10-16 20:21    [W:0.052 / U:0.500 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site