lkml.org 
[lkml]   [2015]   [Oct]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 3/3] phy: rcar-gen3-usb2: add runtime ID/VBUS pin detection
Date
This patch adds support for runtime ID/VBUS pin detection if
the channel 0 of R-Car gen3 is used. So, we are able to use
the channel as both host and peripheral.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
.../devicetree/bindings/phy/rcar-gen3-phy-usb2.txt | 2 +
drivers/phy/phy-rcar-gen3-usb2.c | 43 +++++++++++++++++++++-
2 files changed, 44 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt
index 589f5c0..b30a98a 100644
--- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt
+++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt
@@ -18,6 +18,7 @@ properties. This is because HSUSB has registers to select USB 2.0 host or
peripheral at that channel:
- reg: offset and length of the partial HSUSB register block.
- reg-names: must be "hsusb".
+- interrupts: interrupt specifier for the PHY.

Example (R-Car H3):

@@ -25,6 +26,7 @@ Example (R-Car H3):
compatible = "renesas,usb2-phy-r8a7795";
reg = <0 0xee080200 0 0x700>, <0 0xe6590100 0 0x100>;
reg-names = "usb2_host", "hsusb";
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7795_CLK_EHCI0>,
<&mstp7_clks R8A7795_CLK_HSUSB>;
};
diff --git a/drivers/phy/phy-rcar-gen3-usb2.c b/drivers/phy/phy-rcar-gen3-usb2.c
index 03d7079..40d0005 100644
--- a/drivers/phy/phy-rcar-gen3-usb2.c
+++ b/drivers/phy/phy-rcar-gen3-usb2.c
@@ -12,6 +12,7 @@
* published by the Free Software Foundation.
*/

+#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
#include <linux/of.h>
@@ -26,14 +27,18 @@
#define USB2_SPD_RSM_TIMSET 0x10c
#define USB2_OC_TIMSET 0x110
#define USB2_COMMCTRL 0x600
+#define USB2_OBINTSTA 0x604
+#define USB2_OBINTEN 0x608
#define USB2_VBCTRL 0x60c
#define USB2_LINECTRL1 0x610
#define USB2_ADPCTRL 0x630

/* INT_ENABLE */
+#define USB2_INT_ENABLE_UCOM_INTEN BIT(3)
#define USB2_INT_ENABLE_USBH_INTB_EN BIT(2)
#define USB2_INT_ENABLE_USBH_INTA_EN BIT(1)
-#define USB2_INT_ENABLE_INIT (USB2_INT_ENABLE_USBH_INTB_EN | \
+#define USB2_INT_ENABLE_INIT (USB2_INT_ENABLE_UCOM_INTEN | \
+ USB2_INT_ENABLE_USBH_INTB_EN | \
USB2_INT_ENABLE_USBH_INTA_EN)

/* USBCTR */
@@ -49,6 +54,12 @@
/* COMMCTRL */
#define USB2_COMMCTRL_OTG_PERI BIT(31) /* 1 = Peripheral mode */

+/* OBINTSTA and OBINTEN */
+#define USB2_OBINT_SESSVLDCHG BIT(12)
+#define USB2_OBINT_IDDIGCHG BIT(11)
+#define USB2_OBINT_BITS (USB2_OBINT_SESSVLDCHG | \
+ USB2_OBINT_IDDIGCHG)
+
/* VBCTRL */
#define USB2_VBCTRL_DRVVBUSSEL BIT(8)

@@ -178,6 +189,9 @@ static void rcar_gen3_init_otg(struct rcar_gen3_chan *ch)

tmp = readl(usb2_base + USB2_VBCTRL);
writel(tmp | USB2_VBCTRL_DRVVBUSSEL, usb2_base + USB2_VBCTRL);
+ writel(USB2_OBINT_BITS, usb2_base + USB2_OBINTSTA);
+ tmp = readl(usb2_base + USB2_OBINTEN);
+ writel(tmp | USB2_OBINT_BITS, usb2_base + USB2_OBINTEN);
tmp = readl(usb2_base + USB2_ADPCTRL);
writel(tmp | USB2_ADPCTRL_IDPULLUP, usb2_base + USB2_ADPCTRL);
tmp = readl(usb2_base + USB2_LINECTRL1);
@@ -289,6 +303,23 @@ static struct phy_ops rcar_gen3_phy_usb2_ops = {
.owner = THIS_MODULE,
};

+static irqreturn_t rcar_gen3_phy_usb2_irq(int irq, void *_ch)
+{
+ struct rcar_gen3_chan *ch = _ch;
+ void __iomem *usb2_base = ch->usb2.base;
+ u32 status = readl(usb2_base + USB2_OBINTSTA);
+ irqreturn_t ret = IRQ_NONE;
+
+ if (status & USB2_OBINT_BITS) {
+ dev_dbg(&ch->phy->dev, "%s: %08x\n", __func__, status);
+ writel(USB2_OBINT_BITS, usb2_base + USB2_OBINTSTA);
+ rcar_gen3_device_recognition(ch);
+ ret = IRQ_HANDLED;
+ }
+
+ return ret;
+}
+
static const struct of_device_id rcar_gen3_phy_usb2_match_table[] = {
{ .compatible = "renesas,usb2-phy-r8a7795" },
{ }
@@ -323,9 +354,19 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev)

/* To avoid error message by devm_ioremap_resource() */
if (res) {
+ int ret, irq;
+
channel->hsusb.base = devm_ioremap_resource(dev, res);
if (IS_ERR(channel->hsusb.base))
channel->hsusb.base = NULL;
+ /* call request_irq for OTG */
+ ret = irq = platform_get_irq(pdev, 0);
+ if (irq >= 0)
+ ret = devm_request_irq(dev, irq, rcar_gen3_phy_usb2_irq,
+ IRQF_SHARED, dev_name(dev),
+ channel);
+ if (ret < 0)
+ dev_err(dev, "No irq handler (%d)\n", ret);
}

/* devm_phy_create() will call pm_runtime_enable(dev); */
--
1.9.1


\
 
 \ /
  Last update: 2015-10-13 12:41    [W:0.131 / U:0.392 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site