lkml.org 
[lkml]   [2015]   [Oct]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support
Hi Krzysztof,

On 12 October 2015 at 11:14, Krzysztof Kozlowski
<k.kozlowski@samsung.com> wrote:
> On 12.10.2015 00:46, Anand Moon wrote:
>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104)
>
> This description is not entirely correct. The MMC driver already
> supports these UHS speeds (you did not any code) so you rather enabled
> it (description of bindings says "is supported").
>
> You mentioned DDR50 but I don't see respective property below.
Looks like I missed it, I will add this in the next patch,
>
> How do you know that these modes are really supported? I don't know. Can
> you convince me?
>

>>
>> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
>>
>> ---
>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch
>>
>> Changes Fixed the UHS-I bus speed detedtion on cold boot.
>
> I don't get what is exactly fixed here. What was the error? What is the
> outcome of this fix? The log below is before or after?
>
> Best regards,
> Krzysztof
>
>>
>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
>> [ 2.461743] mmcblk0: p1 p2
>
>> ---
>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++
>> 1 file changed, 4 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>> index 58c06d3..ba4a87b 100644
>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>> @@ -364,6 +364,10 @@
>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
>> bus-width = <4>;
>> cap-sd-highspeed;
>> + sd-uhs-sdr12;
>> + sd-uhs-sdr25;
>> + sd-uhs-sdr50;
>> + sd-uhs-sdr104;
>> };
>>
>> &pinctrl_0 {
>>
>

Changes were made to support Sandisk Ultra UHS-I class 10 card support.
OdroidXU3/XU4 board would not boot up using this card.

Depending on the capability of the UHS-I card, the speed of the card
is selected.
I have just added the enhance capability feature to support them.

On warm boot: i.e reboot of the board.
[ 4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot
req 50000000Hz, actual 50000000HZ div = 0)
[ 4.657555] mmc1: new high speed SDHC card at address aaaa
[ 4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
[ 4.669206] mmcblk0: p1 p2

On cold boot:: ie: power on the board.

[ 4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot
req 100000000Hz, actual 100000000HZ div = 0)
[ 4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
[ 4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
[ 4.650293] IRQ56 no longer affine to CPU7
[ 4.650581] CPU7: shutdown
[ 4.658293] mmcblk0: p1 p2

Note: Their is need to reset the PMIC
S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers
to support this feature consistently on every reboot.

-Anand Moon


\
 
 \ /
  Last update: 2015-10-12 13:21    [W:0.110 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site