lkml.org 
[lkml]   [2015]   [Jan]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH][V2] drivers/usb/serial/mos7840.c: remove unused code
Date
From: Colin Ian King <colin.king@canonical.com>

There is old, unused code that is #defined out by the
use of NOTMOS7840 and NOTMCS7840 - these are not
defined anywhere.

If NOTMOS7840 is defined then the code will break on null
pointer dereferences on mos7840_port. So the code is
currently unused, and broken anyway, so why not just
remove it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
---
drivers/usb/serial/mos7840.c | 60 --------------------------------------------
1 file changed, 60 deletions(-)

diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c
index 220b4be..e4473a9 100644
--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -1309,35 +1309,6 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
const unsigned char *current_position = data;
unsigned char *data1;

-#ifdef NOTMOS7840
- Data = 0x00;
- status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
- mos7840_port->shadowLCR = Data;
- dev_dbg(&port->dev, "%s: LINE_CONTROL_REGISTER is %x\n", __func__, Data);
- dev_dbg(&port->dev, "%s: mos7840_port->shadowLCR is %x\n", __func__, mos7840_port->shadowLCR);
-
- /* Data = 0x03; */
- /* status = mos7840_set_uart_reg(port,LINE_CONTROL_REGISTER,Data); */
- /* mos7840_port->shadowLCR=Data;//Need to add later */
-
- Data |= SERIAL_LCR_DLAB; /* data latch enable in LCR 0x80 */
- status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
- /* Data = 0x0c; */
- /* status = mos7840_set_uart_reg(port,DIVISOR_LATCH_LSB,Data); */
- Data = 0x00;
- status = mos7840_get_uart_reg(port, DIVISOR_LATCH_LSB, &Data);
- dev_dbg(&port->dev, "%s: DLL value is %x\n", __func__, Data);
-
- Data = 0x0;
- status = mos7840_get_uart_reg(port, DIVISOR_LATCH_MSB, &Data);
- dev_dbg(&port->dev, "%s: DLM value is %x\n", __func__, Data);
-
- Data = Data & ~SERIAL_LCR_DLAB;
- dev_dbg(&port->dev, "%s: mos7840_port->shadowLCR is %x\n", __func__, mos7840_port->shadowLCR);
- status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-#endif
-
if (mos7840_port_paranoia_check(port, __func__))
return -1;

@@ -1614,37 +1585,6 @@ static int mos7840_calc_baud_rate_divisor(struct usb_serial_port *port,
*clk_sel_val = 0x70;
}
return 0;
-
-#ifdef NOTMCS7840
-
- for (i = 0; i < ARRAY_SIZE(mos7840_divisor_table); i++) {
- if (mos7840_divisor_table[i].BaudRate == baudrate) {
- *divisor = mos7840_divisor_table[i].Divisor;
- return 0;
- }
- }
-
- /* After trying for all the standard baud rates *
- * Try calculating the divisor for this baud rate */
-
- if (baudrate > 75 && baudrate < 230400) {
- /* get the divisor */
- custom = (__u16) (230400L / baudrate);
-
- /* Check for round off */
- round1 = (__u16) (2304000L / baudrate);
- round = (__u16) (round1 - (custom * 10));
- if (round > 4)
- custom++;
- *divisor = custom;
-
- dev_dbg(&port->dev, " Baud %d = %d\n", baudrate, custom);
- return 0;
- }
-
- dev_dbg(&port->dev, "%s", " Baud calculation Failed...\n");
- return -1;
-#endif
}

/*****************************************************************************
--
2.1.4


\
 
 \ /
  Last update: 2015-01-19 14:41    [W:0.045 / U:0.288 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site