lkml.org 
[lkml]   [2015]   [Jan]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] remoteproc: microblaze: Document device tree bindings
Date
Add device tree binding documentation for the Microblaze remoteproc
on Xilinx Zynq.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---

.../bindings/remoteproc/mb_remoteproc.txt | 46 ++++++++++++++++++++++
1 file changed, 46 insertions(+)
create mode 100644 Documentation/devicetree/bindings/remoteproc/mb_remoteproc.txt

diff --git a/Documentation/devicetree/bindings/remoteproc/mb_remoteproc.txt b/Documentation/devicetree/bindings/remoteproc/mb_remoteproc.txt
new file mode 100644
index 000000000000..a2490eac0208
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/mb_remoteproc.txt
@@ -0,0 +1,46 @@
+Xilinx ARM-Microblaze remoteproc driver
+
+This driver requires specific Zynq hardware design where Microblaze is added
+to the programmable logic.
+Microblaze is connected with PS block via axi bus connected to PS HP port
+to ensure access to PS DDR.
+Communication channels are done via soft GPIO IP connected to PS block
+and to Microblaze. There are also 2 gpio control signals reset and debug
+which are used for resetting Microblaze.
+
+Required properties:
+- compatible : Should be "xlnx,mb_remoteproc"
+- reg : Address and length of the ddr address space
+- bram: Phandle to bram controller which can access Microblaze BRAM
+- bram-firmware : Microblaze BRAM bootloader name
+- firmware : Default firmware name which can be override by
+ "firmware" module parameter
+- reset : Gpio phandle which reset Microblaze remoteproc
+- debug : Gpio phandle which setup Microblaze to debug state
+- ipino : Gpio phandle for Microblaze to ARM communication
+- vring0 : Gpio phandle for ARM to Microblaze communication vring 0
+- vring1 : Gpio phandle for ARM to Microblaze communication vring 1
+
+Microblaze SoC can be also connected to the PS block via a axi bus.
+That's why there is the option to allocate interrupts for Microblaze use only.
+The driver will allocate interrupts to itself and Microblaze sw has to ensure
+that interrupts are properly enabled and handled by Microblaze interrupt
+controller.
+
+Optional properties:
+ - interrupts : Interrupt mapping for remoteproc
+ - interrupt-parent : Phandle for the interrupt controller
+
+Example:
+mb_remoteproc@800000 {
+ compatible = "xlnx,mb_remoteproc";
+ reg = < 0x8000000 0x8000000 >;
+ bram = <&axi_bram_ctrl_0>;
+ bram-firmware = "mb.bin";
+ firmware = "image.elf";
+ reset = <&zynq_gpio_reset 1 0>;
+ debug = <&zynq_gpio_reset 0 0>;
+ ipino = <&zynq_gpio_vring 0 0>;
+ vring0 = <&zynq_gpio_vring 1 0>;
+ vring1 = <&zynq_gpio_vring 2 0>;
+};
--
1.8.2.3
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2015-01-19 11:41    [W:0.078 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site