lkml.org 
[lkml]   [2014]   [Sep]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] tty: omap-serial: fix division by zero
On Wed, Sep 24, 2014 at 01:08:52AM -0700, Greg Kroah-Hartman wrote:
> On Wed, Sep 24, 2014 at 09:55:21AM +0200, Frans Klaver wrote:
> > If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
> > calculated n values in serial_omap_is_baud_mode16() may become 0. This
> > causes a division by zero when calculating the difference between
> > calculated and desired baud rates. To prevent this, cap the n13 and n16
> > values on 1.
> >
> > Division by zero in kernel.
> > [<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
> > [<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
> > [<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
> > [<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
> > [<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
> > [<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
> > [<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
> > [<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
> > [<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
> > [<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
> > [<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
> > [<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
> > [<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
> >
> > Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
> > ---
> > drivers/tty/serial/omap-serial.c | 12 ++++++++++--
> > 1 file changed, 10 insertions(+), 2 deletions(-)
>
> Should this go to the stable kernel trees as well?

It's been there for a while. Introduced in 5fe2123647c1508 "OMAP/serial:
Support 1Mbaud and similar baudrates that require Mode16 instead of
Mode13" (v3.9). It's probably a good idea to do so. stable@... needs a
cc?

Frans


\
 
 \ /
  Last update: 2014-09-24 11:21    [W:0.097 / U:0.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site