lkml.org 
[lkml]   [2014]   [Sep]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH 2/5] MN10300: Remove Kconfig symbols depending on GDBSTUB
From
Date
The Kconfig symbol GDBSTUB was removed. Remove all symbols (indirectly)
depending on it. And remove it as an (optional) dependency for the
symbol KERNEL_DEBUGGER.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
---
arch/mn10300/Kconfig.debug | 105 +--------------------------------------------
1 file changed, 1 insertion(+), 104 deletions(-)

diff --git a/arch/mn10300/Kconfig.debug b/arch/mn10300/Kconfig.debug
index 6a8c7e8d6156..a1acb29f6b2a 100644
--- a/arch/mn10300/Kconfig.debug
+++ b/arch/mn10300/Kconfig.debug
@@ -30,111 +30,8 @@ config KPROBES
for kernel debugging, non-intrusive instrumentation and testing.
If in doubt, say "N".

-config GDBSTUB_IMMEDIATE
- bool "Break into GDB stub immediately"
- depends on GDBSTUB
- help
- If you say Y here, GDB stub will break into the program as soon as
- possible, leaving the program counter at the beginning of
- start_kernel() in init/main.c.
-
-config GDBSTUB_ALLOW_SINGLE_STEP
- bool "Allow software single-stepping in GDB stub"
- depends on GDBSTUB && !SMP && !PREEMPT
- help
- Allow GDB stub to perform software single-stepping through the
- kernel. This doesn't work very well on SMP or preemptible kernels as
- it uses temporary breakpoints to emulate single-stepping.
-
-config GDB_CONSOLE
- bool "Console output to GDB"
- depends on GDBSTUB
- help
- If you are using GDB for remote debugging over a serial port and
- would like kernel messages to be formatted into GDB $O packets so
- that GDB prints them as program output, say 'Y'.
-
-config GDBSTUB_DEBUGGING
- bool "Debug GDB stub by messages to serial port"
- depends on GDBSTUB
- help
- This causes debugging messages to be displayed at various points
- during execution of the GDB stub routines. Such messages will be
- displayed on ttyS0 if that isn't the GDB stub's port, or ttySM0
- otherwise.
-
-config GDBSTUB_DEBUG_ENTRY
- bool "Debug GDB stub entry"
- depends on GDBSTUB_DEBUGGING
- help
- This option causes information to be displayed about entry to or exit
- from the main GDB stub routine.
-
-config GDBSTUB_DEBUG_PROTOCOL
- bool "Debug GDB stub protocol"
- depends on GDBSTUB_DEBUGGING
- help
- This option causes information to be displayed about the GDB remote
- protocol messages generated exchanged with GDB.
-
-config GDBSTUB_DEBUG_IO
- bool "Debug GDB stub I/O"
- depends on GDBSTUB_DEBUGGING
- help
- This option causes information to be displayed about GDB stub's
- low-level I/O.
-
-config GDBSTUB_DEBUG_BREAKPOINT
- bool "Debug GDB stub breakpoint management"
- depends on GDBSTUB_DEBUGGING
- help
- This option causes information to be displayed about GDB stub's
- breakpoint management.
-
-choice
- prompt "GDB stub port"
- default GDBSTUB_ON_TTYSM0
- depends on GDBSTUB
- help
- Select the serial port used for GDB-stub.
-
-config GDBSTUB_ON_TTYSM0
- bool "/dev/ttySM0 [SIF0]"
- depends on MN10300_TTYSM0
- select GDBSTUB_ON_TTYSMx
-
-config GDBSTUB_ON_TTYSM1
- bool "/dev/ttySM1 [SIF1]"
- depends on MN10300_TTYSM1
- select GDBSTUB_ON_TTYSMx
-
-config GDBSTUB_ON_TTYSM2
- bool "/dev/ttySM2 [SIF2]"
- depends on MN10300_TTYSM2
- select GDBSTUB_ON_TTYSMx
-
-config GDBSTUB_ON_TTYS0
- bool "/dev/ttyS0"
- select GDBSTUB_ON_TTYSx
-
-config GDBSTUB_ON_TTYS1
- bool "/dev/ttyS1"
- select GDBSTUB_ON_TTYSx
-
-endchoice
-
-config GDBSTUB_ON_TTYSMx
- bool
- depends on GDBSTUB_ON_TTYSM0 || GDBSTUB_ON_TTYSM1 || GDBSTUB_ON_TTYSM2
- default y
-
-config GDBSTUB_ON_TTYSx
- bool
- depends on GDBSTUB_ON_TTYS0 || GDBSTUB_ON_TTYS1
- default y
-
endmenu

config KERNEL_DEBUGGER
def_bool y
- depends on GDBSTUB || KGDB
+ depends on KGDB
--
1.9.3


\
 
 \ /
  Last update: 2014-09-18 21:01    [W:0.030 / U:0.788 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site