lkml.org 
[lkml]   [2014]   [Sep]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 2/4] pinctrl: Device tree bindings for Qualcomm PMIC MPP block
Date
DeviceTree binding documentation for Qualcomm SPMI PMIC MPP
pinctrl drivers.

Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
---
.../devicetree/bindings/pinctrl/qcom,pmic-mpp.txt | 159 +++++++++++++++++++++
include/dt-bindings/pinctrl/qcom,pmic-mpp.h | 44 ++++++
2 files changed, 203 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
create mode 100644 include/dt-bindings/pinctrl/qcom,pmic-mpp.h

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
new file mode 100644
index 0000000..9d4779f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
@@ -0,0 +1,159 @@
+Qualcomm PMIC Multi-Purpose Pin (MPP) block
+
+This binding describes the MPP block(s) found in the 8xxx series
+of PMIC's from Qualcomm.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,spmi-pmic-mpp"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Register base of the MPP block and length.
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Must contain an array of encoded interrupt specifiers for
+ each available gpio
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: Mark the device node as a GPIO controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Must be 2;
+ the first cell will be used to define gpio number and the
+ second denotes the flags for this gpio
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin or a list of pins. This configuration can include the
+mux function to select on those pin(s), and various pin configuration
+parameters, as listed below.
+
+SUBNODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode. Valid pins are:
+ mpp1-mpp4 for pm8841
+ mpp1-mpp8 for pm8941
+ mpp1-mpp4 for pma8084
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Valid values are:
+ "normal",
+ "paired",
+ "dtest1",
+ "dtest2",
+ "dtest3",
+ "dtest4"
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configured as no pull.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <u32>
+ Definition: The specified pins should be configured as pull up.
+ Valid values are 600, 10000 and 30000 in bidirectional mode only,
+ i.e. when operating in qcom,analog-mode and input and outputs are
+ enabled. The hardware ignores the configuration when operating in
+ other modes.
+
+- bias-high-impedance:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins will put in high-Z mode and disabled.
+
+- input-enable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are put in input mode, i.e. thier input
+ buffer is enabled
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+
+- power-source:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the power source for the specified pins. Valid power
+ sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+- qcom,analog-mode:
+ Usage: optional
+ Value type: <none>
+ Definition: Selects Analog mode of operation: combined with input-enable
+ and/or output-high, output-log MPP could operate as Bidirectional
+ Logic, Analog Input, Analog Output.
+
+- qcom,amux-route:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the source for analog input. Valid values are
+ defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+ PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6...
+
+Example:
+
+ mpps@a000 {
+ compatible = "qcom,pm8841-mpp";
+ reg = <0xa000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm8841_default>;
+
+ pm8841_default: default {
+ gpio {
+ pins = "mpp1", "mpp2", "mpp3", "mpp4";
+ function = "normal";
+ input-enable;
+ power-source = <PM8841_MPP_S3>;
+ };
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/qcom,pmic-mpp.h b/include/dt-bindings/pinctrl/qcom,pmic-mpp.h
new file mode 100644
index 0000000..d2c7dab
--- /dev/null
+++ b/include/dt-bindings/pinctrl/qcom,pmic-mpp.h
@@ -0,0 +1,44 @@
+/*
+ * This header provides constants for the Qualcomm PMIC's
+ * Multi-Purpose Pin binding.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_QCOM_PMIC_MPP_H
+#define _DT_BINDINGS_PINCTRL_QCOM_PMIC_MPP_H
+
+/* power-source */
+#define PM8841_MPP_VPH 0
+#define PM8841_MPP_S3 2
+
+#define PM8941_MPP_VPH 0
+#define PM8941_MPP_L1 1
+#define PM8941_MPP_S3 2
+#define PM8941_MPP_L6 3
+
+#define PMA8084_MPP_VPH 0
+#define PMA8084_MPP_L1 1
+#define PMA8084_MPP_S4 2
+#define PMA8084_MPP_L6 3
+
+/*
+ * Analog Input - Set the source for analog input.
+ * To be used with "qcom,amux-route" property
+ */
+#define PMIC_MPP_AMUX_ROUTE_CH5 0
+#define PMIC_MPP_AMUX_ROUTE_CH6 1
+#define PMIC_MPP_AMUX_ROUTE_CH7 2
+#define PMIC_MPP_AMUX_ROUTE_CH8 3
+#define PMIC_MPP_AMUX_ROUTE_ABUS1 4
+#define PMIC_MPP_AMUX_ROUTE_ABUS2 5
+#define PMIC_MPP_AMUX_ROUTE_ABUS3 6
+#define PMIC_MPP_AMUX_ROUTE_ABUS4 7
+
+/* To be used with "function" */
+#define PMIC_MPP_FUNC_NORMAL "normal"
+#define PMIC_MPP_FUNC_PAIRED "paired"
+#define PMIC_MPP_FUNC_DTEST1 "dtest1"
+#define PMIC_MPP_FUNC_DTEST2 "dtest2"
+#define PMIC_MPP_FUNC_DTEST3 "dtest3"
+#define PMIC_MPP_FUNC_DTEST4 "dtest4"
+
+#endif
--
1.9.1


\
 
 \ /
  Last update: 2014-09-15 17:21    [W:0.104 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site