lkml.org 
[lkml]   [2014]   [Aug]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 2/2] usb: dwc2: add 'mode' which based on Kconfig select or dts setting
Date
According to the "dr_mode", the otg controller can work as
device role during firmware period, and work as host role in
the kernel, without use of usb_id pin. As the commit "usb: dwc3:
set 'mode' based on selected Kconfig choices".

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

---

Changes in v3:
- fix the odd spacing in dwc2_hsotg struct
- From Jingoo's suggestion:
change the commit message

Changes in v2:
- put spaces around '+' operator
- expand the comment for dr_mode
- handle dr_mode is USB_DR_MODE_OTG

drivers/usb/dwc2/core.c | 18 ++++++++++++++++++
drivers/usb/dwc2/core.h | 5 +++++
drivers/usb/dwc2/platform.c | 12 ++++++++++++
3 files changed, 35 insertions(+)

diff --git a/drivers/usb/dwc2/core.c b/drivers/usb/dwc2/core.c
index 27d2c9b..738bec2 100644
--- a/drivers/usb/dwc2/core.c
+++ b/drivers/usb/dwc2/core.c
@@ -118,6 +118,7 @@ static int dwc2_core_reset(struct dwc2_hsotg *hsotg)
{
u32 greset;
int count = 0;
+ u32 gusbcfg;

dev_vdbg(hsotg->dev, "%s()\n", __func__);

@@ -148,6 +149,23 @@ static int dwc2_core_reset(struct dwc2_hsotg *hsotg)
}
} while (greset & GRSTCTL_CSFTRST);

+ if (hsotg->dr_mode == USB_DR_MODE_HOST) {
+ gusbcfg = readl(hsotg->regs + GUSBCFG);
+ gusbcfg &= ~GUSBCFG_FORCEDEVMODE;
+ gusbcfg |= GUSBCFG_FORCEHOSTMODE;
+ writel(gusbcfg, hsotg->regs + GUSBCFG);
+ } else if (hsotg->dr_mode == USB_DR_MODE_PERIPHERAL) {
+ gusbcfg = readl(hsotg->regs + GUSBCFG);
+ gusbcfg &= ~GUSBCFG_FORCEHOSTMODE;
+ gusbcfg |= GUSBCFG_FORCEDEVMODE;
+ writel(gusbcfg, hsotg->regs + GUSBCFG);
+ } else if (hsotg->dr_mode == USB_DR_MODE_OTG) {
+ gusbcfg = readl(hsotg->regs + GUSBCFG);
+ gusbcfg &= ~GUSBCFG_FORCEHOSTMODE;
+ gusbcfg &= ~GUSBCFG_FORCEDEVMODE;
+ writel(gusbcfg, hsotg->regs + GUSBCFG);
+ }
+
/*
* NOTE: This long sleep is _very_ important, otherwise the core will
* not stay in host mode after a connector ID change!
diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h
index 1efd10c..52a4fd2 100644
--- a/drivers/usb/dwc2/core.h
+++ b/drivers/usb/dwc2/core.h
@@ -501,6 +501,10 @@ struct dwc2_hw_params {
* a_peripheral and b_device=>b_host) this may not match
* the core, but allows the software to determine
* transitions
+ * @dr_mode: Requested mode of operation, one of following:
+ * - USB_DR_MODE_PERIPHERAL
+ * - USB_DR_MODE_HOST
+ * - USB_DR_MODE_OTG
* @queuing_high_bandwidth: True if multiple packets of a high-bandwidth
* transfer are in process of being queued
* @srp_success: Stores status of SRP request in the case of a FS PHY
@@ -592,6 +596,7 @@ struct dwc2_hsotg {
/** Params to actually use */
struct dwc2_core_params *core_params;
enum usb_otg_state op_state;
+ enum usb_dr_mode dr_mode;

unsigned int queuing_high_bandwidth:1;
unsigned int srp_success:1;
diff --git a/drivers/usb/dwc2/platform.c b/drivers/usb/dwc2/platform.c
index a10e7a3..4d2c738 100644
--- a/drivers/usb/dwc2/platform.c
+++ b/drivers/usb/dwc2/platform.c
@@ -42,6 +42,8 @@
#include <linux/of_device.h>
#include <linux/platform_device.h>

+#include <linux/usb/of.h>
+
#include "core.h"
#include "hcd.h"

@@ -171,6 +173,16 @@ static int dwc2_driver_probe(struct platform_device *dev)
dev_dbg(&dev->dev, "mapped PA %08lx to VA %p\n",
(unsigned long)res->start, hsotg->regs);

+ hsotg->dr_mode = of_usb_get_dr_mode(dev->dev.of_node);
+
+ if (IS_ENABLED(CONFIG_USB_DWC2_HOST))
+ hsotg->dr_mode = USB_DR_MODE_HOST;
+ else if (IS_ENABLED(CONFIG_USB_DWC2_GADGET))
+ hsotg->dr_mode = USB_DR_MODE_PERIPHERAL;
+
+ if (hsotg->dr_mode == USB_DR_MODE_UNKNOWN)
+ hsotg->dr_mode = USB_DR_MODE_OTG;
+
retval = dwc2_hcd_init(hsotg, irq, params);
if (retval)
return retval;
--
1.9.1


\
 
 \ /
  Last update: 2014-08-04 16:21    [W:0.089 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site