lkml.org 
[lkml]   [2014]   [Aug]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/2] thermal: rockchip: add driver for thermal
Hi Dmtry,

在 2014年08月27日 08:11, Dmitry Torokhov 写道:
> Hi Caesar,
>
> On Wed, Aug 27, 2014 at 07:41:42AM +0800, Caesar Wang wrote:
>> Thermal is TS-ADC Controller module supports user-defined mode and automatic mode.
>>
>> User-defined mode refers,TSADC all the control signals entirely by software
>> writing to register for direct control.
>>
>> Automaic mode refers to the module automatically poll TSADC output,and the results
>> Were checked.
>>
>> If you find that the temperature High in a period of time, an interrupt is generated
>> to the processor down-measures taken;if the temperature over a period of time High,
>> the resulting TSHUT gave CRU module,let it reset the entire chip, or via GPIO give PMIC.
>>
>> Signed-off-by: zhaoyifeng <zyf@rock-chips.com>
>> Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
>> Change-Id: I00e7df78c497704657aff16e602aa56b4c14c6f5
>> ---
>> drivers/thermal/Kconfig | 9 +
>> drivers/thermal/Makefile | 1 +
>> drivers/thermal/rockchip_thermal.c | 644 ++++++++++++++++++++++++++++++++++++
>> 3 files changed, 654 insertions(+)
>> create mode 100644 drivers/thermal/rockchip_thermal.c
>>
>> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
>> index 74226dc..43d2400 100644
>> --- a/drivers/thermal/Kconfig
>> +++ b/drivers/thermal/Kconfig
>> @@ -141,6 +141,15 @@ config SPEAR_THERMAL
>> Enable this to plug the SPEAr thermal sensor driver into the Linux
>> thermal framework.
>>
>> +config ROCKCHIP_THERMAL
>> + tristate "Rockchip thermal driver"
>> + depends on ARCH_ROCKCHIP
>> + help
>> + Support for Temperature Sensor ADC (TS-ADC) found on Rockchip SoCs.
>> + It supports one critical trip point and one passive trip point. The
>> + cpufreq is used as the cooling device to throttle CPUs when the
>> + passive trip is crossed.
>> +
>> config RCAR_THERMAL
>> tristate "Renesas R-Car thermal driver"
>> depends on ARCH_SHMOBILE || COMPILE_TEST
>> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
>> index 419c3cd..009a457 100644
>> --- a/drivers/thermal/Makefile
>> +++ b/drivers/thermal/Makefile
>> @@ -20,6 +20,7 @@ thermal_sys-$(CONFIG_CPU_THERMAL) += cpu_cooling.o
>>
>> # platform thermal drivers
>> obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
>> +obj-$(CONFIG_ROCKCHIP_THERMAL) += rockchip_thermal.o
>> obj-$(CONFIG_RCAR_THERMAL) += rcar_thermal.o
>> obj-$(CONFIG_KIRKWOOD_THERMAL) += kirkwood_thermal.o
>> obj-y += samsung/
>> diff --git a/drivers/thermal/rockchip_thermal.c b/drivers/thermal/rockchip_thermal.c
>> new file mode 100644
>> index 0000000..dea4dc3
>> --- /dev/null
>> +++ b/drivers/thermal/rockchip_thermal.c
>> @@ -0,0 +1,644 @@
>> +/*
>> + * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
>> + *
>> + * This program is free software; you can redistribute it and/or modify it
>> + * under the terms and conditions of the GNU General Public License,
>> + * version 2, as published by the Free Software Foundation.
>> + *
>> + * This program is distributed in the hope it will be useful, but WITHOUT
>> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
>> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
>> + * more details.
>> + *
>> +*/
>> +
>> +#include <linux/clk.h>
>> +#include <linux/io.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regulator/consumer.h>
>> +#include <linux/cpu_cooling.h>
>> +#include "thermal_core.h"
>> +
>> +enum rockchip_thermal_trip {
>> + ROCKCHIP_TRIP_PASSIVE,
>> + ROCKCHIP_TRIP_CRITICAL,
>> + ROCKCHIP_TRIP_NUM,
>> +};
>> +
>> +struct rockchip_thermal_data {
>> + const struct rockchip_tsadc_platform_data *pdata;
>> + struct thermal_zone_device *tz;
>> + struct thermal_cooling_device *cdev;
>> + enum thermal_device_mode mode;
>> + void __iomem *regs;
>> +
>> + signed long temp_passive;
>> + signed long temp_critical;
>> + signed long temp_force_shut;
>> + signed long alarm_temp;
>> + signed long last_temp;
>> + bool irq_enabled;
>> + int irq;
>> + struct clk *tsadc_clk;
>> + struct clk *tsadc_pclk;
>> +};
>> +
>> +struct rockchip_tsadc_platform_data {
>> + u8 irq_en;
>> + signed long temp_passive;
>> + signed long temp_critical;
>> + signed long temp_force_shut;
>> + int passive_delay;
>> + int polling_delay;
>> +
>> + int (*irq_handle)(void __iomem *reg);
>> + int (*initialize)(void __iomem *reg, signed long temp_force_shut);
>> + int (*control)(void __iomem *reg, bool on);
>> + u32 (*code_to_temp)(int temp);
>> + u32 (*temp_to_code)(int temp);
>> + void (*set_alarm_temp)(void __iomem *regs, signed long temp);
>> +};
>> +
>> +/*TSADC V2 Sensor info define:*/
>> +#define TSADCV2_AUTO_CON 0x04
>> +#define TSADCV2_INT_EN 0x08
>> +#define TSADCV2_INT_PD 0x0c
>> +#define TSADCV2_DATA1 0x24
>> +#define TSADCV2_COMP1_INT 0x34
>> +#define TSADCV2_COMP1_SHUT 0x44
>> +#define TSADCV2_AUTO_PERIOD 0x68
>> +#define TSADCV2_AUTO_PERIOD_HT 0x6c
>> +
>> +#define TSADCV2_AUTO_SRC1_EN (1 << 5)
>> +#define TSADCV2_AUTO_EN (1 << 0)
>> +#define TSADCV2_AUTO_DISABLE ~(1 << 0)
>> +#define TSADCV2_AUTO_STAS_BUSY (1 << 16)
>> +#define TSADCV2_AUTO_STAS_BUSY_MASK (1 << 16)
>> +#define TSADCV2_SHUT_2GPIO_SRC1_EN (1 << 5)
>> +#define TSADCV2_INT_SRC1_EN (1 << 1)
>> +#define TSADCV2_SHUT_SRC1_STATUS (1 << 5)
>> +#define TSADCV2_INT_SRC1_STATUS (1 << 1)
>> +
>> +#define TSADCV2_DATA_MASK 0xfff
>> +#define TSADCV2_HIGHT_INT_DEBOUNCE 0x60
>> +#define TSADCV2_HIGHT_TSHUT_DEBOUNCE 0x64
>> +#define TSADCV2_HIGHT_INT_DEBOUNCE_TIME 0x0a
>> +#define TSADCV2_HIGHT_TSHUT_DEBOUNCE_TIME 0x0a
>> +#define TSADCV2_AUTO_PERIOD_TIME 0x03e8
>> +#define TSADCV2_AUTO_PERIOD_HT_TIME 0x64
>> +
>> +struct tsadc_table {
>> + int code;
>> + int temp;
>> +};
>> +
>> +static const struct tsadc_table v2_code_table[] = {
>> + {TSADCV2_DATA_MASK, -40},
>> + {3800, -40},
>> + {3792, -35},
>> + {3783, -30},
>> + {3774, -25},
>> + {3765, -20},
>> + {3756, -15},
>> + {3747, -10},
>> + {3737, -5},
>> + {3728, 0},
>> + {3718, 5},
>> + {3708, 10},
>> + {3698, 15},
>> + {3688, 20},
>> + {3678, 25},
>> + {3667, 30},
>> + {3656, 35},
>> + {3645, 40},
>> + {3634, 45},
>> + {3623, 50},
>> + {3611, 55},
>> + {3600, 60},
>> + {3588, 65},
>> + {3575, 70},
>> + {3563, 75},
>> + {3550, 80},
>> + {3537, 85},
>> + {3524, 90},
>> + {3510, 95},
>> + {3496, 100},
>> + {3482, 105},
>> + {3467, 110},
>> + {3452, 115},
>> + {3437, 120},
>> + {3421, 125},
>> + {0, 125},
>> +};
>> +
>> +static int rk_tsadcv2_irq_handle(void __iomem *regs)
>> +{
>> + u32 val;
>> +
>> + val = readl_relaxed(regs + TSADCV2_INT_PD);
>> + writel_relaxed(val & ~(1 << 8), regs + TSADCV2_INT_PD);
>> +
>> + return 0;
>> +}
>> +
>> +static u32 rk_tsadcv2_temp_to_code(int temp)
>> +{
>> + u32 code = 0;
>> + int i;
>> +
>> + for (i = 0; i < ARRAY_SIZE(v2_code_table) - 1; i++) {
>> + if (temp <= v2_code_table[i].temp && temp >
>> + v2_code_table[i - 1].temp)
> Since array is sorted you should be able to do only one comparison, on
> the upper bound. Also, as soon as you find the code you can return it,
> there is no need to continue scanning the array.

sound reasonable, I will fix it ,as the folllow:

for (i = 0; i < ARRAY_SIZE(v2_code_table) - 1; i++) {
if (temp <= v2_code_table[i].temp && temp >
v2_code_table[i - 1].temp){
code = v2_code_table[i].code;
break;
}
}

>> + code = v2_code_table[i].code;
>> + }
>> + return code;
>> +}
>> +
>> +static u32 rk_tsadcv2_code_to_temp(int code)
>> +{
>> + u32 temp = 0;
>> + int i;
>> +
>> + for (i = 0; i < ARRAY_SIZE(v2_code_table) - 1; i++) {
>> + if (code <= v2_code_table[i].code && code >
>> + v2_code_table[i + 1].code)
>> + temp = v2_code_table[i].temp;
>> + }
>> + return temp;
>> +}
>> +
Ditto,
>> +static int rk_tsadcv2_initialize(void __iomem *regs,
>> + signed long temp_force_shut)
>> +{
>> + int shutdown_value;
>> +
>> + shutdown_value = rk_tsadcv2_temp_to_code(temp_force_shut);
>> + /* Enable measurements at ~ 10 Hz */
>> + writel_relaxed(0, regs + TSADCV2_AUTO_CON);
>> + writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, regs + TSADCV2_AUTO_PERIOD);
>> + writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME, regs +
>> + TSADCV2_AUTO_PERIOD_HT);
>> + writel_relaxed(shutdown_value, regs + TSADCV2_COMP1_SHUT);
>> + writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_TIME, regs +
>> + TSADCV2_HIGHT_INT_DEBOUNCE);
>> + writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_TIME, regs +
>> + TSADCV2_HIGHT_TSHUT_DEBOUNCE);
>> + writel_relaxed(TSADCV2_SHUT_2GPIO_SRC1_EN | TSADCV2_INT_SRC1_EN, regs +
>> + TSADCV2_INT_EN);
>> + writel_relaxed(TSADCV2_AUTO_SRC1_EN | TSADCV2_AUTO_EN, regs +
>> + TSADCV2_AUTO_CON);
>> + return 0;
>> +}
>> +
>> +static int rk_tsadcv2_control(void __iomem *regs, bool on)
>> +{
>> + u32 val;
>> +
>> + if (on) {
>> + val = readl_relaxed(regs + TSADCV2_AUTO_CON);
>> + writel_relaxed(val | TSADCV2_AUTO_EN, regs + TSADCV2_AUTO_CON);
>> + } else {
>> + val = readl_relaxed(regs + TSADCV2_AUTO_CON);
>> + writel_relaxed(val & TSADCV2_AUTO_DISABLE,
>> + regs + TSADCV2_AUTO_CON);
>> + }
>> + return 0;
>> +}
>> +
>> +static void rk_tsadcv2_alarm_temp(void __iomem *regs, signed long alarm_temp)
>> +{
>> + int alarm_value;
>> +
>> + alarm_value = rk_tsadcv2_temp_to_code(alarm_temp);
>> + writel_relaxed(alarm_value, regs + TSADCV2_COMP1_INT);
>> +}
>> +
>> +struct rockchip_tsadc_platform_data const rk3288_tsadc_data = {
>> + .irq_en = 1,
>> + .temp_passive = 85000,
>> + .temp_critical = 100000,
>> + .temp_force_shut = 120000,
>> + .passive_delay = 2000,
>> + .polling_delay = 1000,
>> + .irq_handle = rk_tsadcv2_irq_handle,
>> + .initialize = rk_tsadcv2_initialize,
>> + .control = rk_tsadcv2_control,
>> + .code_to_temp = rk_tsadcv2_code_to_temp,
>> + .temp_to_code = rk_tsadcv2_temp_to_code,
>> + .set_alarm_temp = rk_tsadcv2_alarm_temp,
>> +};
>> +
>> +static const struct of_device_id of_rockchip_thermal_match[] = {
>> + {
>> + .compatible = "rockchip,rk3288-tsadc",
>> + .data = (void *)&rk3288_tsadc_data,
>> + },
>> + { /* end */ },
>> +};
>> +MODULE_DEVICE_TABLE(of, of_rockchip_thermal_match);
>> +
>> +static void rockchip_set_alarm_temp(struct rockchip_thermal_data *data,
>> + signed long alarm_temp)
>> +{
>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>> +
>> + data->alarm_temp = alarm_temp;
>> + if (p_tsadc_data->set_alarm_temp)
>> + p_tsadc_data->set_alarm_temp(data->regs, alarm_temp);
>> +}
>> +
>> +static int rockchip_get_temp(struct thermal_zone_device *tz,
>> + unsigned long *temp)
>> +{
>> + struct rockchip_thermal_data *data = tz->devdata;
>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>> + u32 val;
>> +
>> + val = readl_relaxed(data->regs + TSADCV2_DATA1);
>> + *temp = p_tsadc_data->code_to_temp(val);
>> +
>> + /* Update alarm value to next higher trip point */
>> + if (data->alarm_temp == data->temp_passive && *temp >=
>> + data->temp_passive)
>> + rockchip_set_alarm_temp(data, data->temp_critical);
>> +
>> + if (data->alarm_temp == data->temp_critical && *temp <
>> + data->temp_passive) {
>> + rockchip_set_alarm_temp(data, data->temp_passive);
>> + dev_dbg(&tz->device, "thermal alarm off: T < %lu\n",
>> + data->alarm_temp / 1000);
>> + }
>> +
>> + if (*temp != data->last_temp) {
>> + dev_dbg(&tz->device, "millicelsius: %ld\n", *temp);
>> + data->last_temp = *temp;
>> + }
>> +
>> + /* Reenable alarm IRQ if temperature below alarm temperature */
>> + if (!data->irq_enabled && *temp < data->alarm_temp) {
>> + data->irq_enabled = true;
>> + enable_irq(data->irq);
>> + }
>> + return 0;
>> +}
>> +
>> +static int rockchip_thermal_initialize(struct rockchip_thermal_data *data)
>> +{
>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>> +
>> + if (p_tsadc_data->initialize)
>> + p_tsadc_data->initialize(data->regs, data->temp_force_shut);
>> + rockchip_set_alarm_temp(data, data->temp_passive);
>> + return 0;
>> +}
>> +
>> +static void rockchip_thermal_control(struct rockchip_thermal_data *data,
>> + bool on)
>> +{
>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>> +
>> + if (p_tsadc_data->control)
>> + p_tsadc_data->control(data->regs, on);
>> +
>> + if (on) {
>> + data->irq_enabled = true;
>> + data->mode = THERMAL_DEVICE_ENABLED;
>> + } else {
>> + data->irq_enabled = false;
>> + data->mode = THERMAL_DEVICE_DISABLED;
>> + }
>> +}
>> +
>> +static int rockchip_get_mode(struct thermal_zone_device *tz,
>> + enum thermal_device_mode *mode)
>> +{
>> + struct rockchip_thermal_data *data = tz->devdata;
>> +
>> + *mode = data->mode;
>> + return 0;
>> +}
>> +
>> +static int rockchip_set_mode(struct thermal_zone_device *tz,
>> + enum thermal_device_mode mode)
>> +{
>> + struct rockchip_thermal_data *data = tz->devdata;
>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>> +
>> + if (mode == THERMAL_DEVICE_ENABLED) {
>> + tz->polling_delay = p_tsadc_data->polling_delay;
>> + tz->passive_delay = p_tsadc_data->passive_delay;
>> + rockchip_thermal_control(data, true);
>> + if (!data->irq_enabled) {
>> + data->irq_enabled = true;
>> + enable_irq(data->irq);
>> + }
>> + } else {
>> + rockchip_thermal_control(data, false);
>> + tz->polling_delay = 0;
>> + tz->passive_delay = 0;
>> + if (data->irq_enabled) {
>> + disable_irq(data->irq);
>> + data->irq_enabled = false;
>> + }
>> + }
>> +
>> + data->mode = mode;
>> + thermal_zone_device_update(tz);
>> + return 0;
>> +}
>> +
>> +static int rockchip_get_trip_type(struct thermal_zone_device *tz, int trip,
>> + enum thermal_trip_type *type)
>> +{
>> + *type = (trip == ROCKCHIP_TRIP_PASSIVE) ? THERMAL_TRIP_PASSIVE :
>> + THERMAL_TRIP_CRITICAL;
>> + return 0;
>> +}
>> +
>> +static int rockchip_get_crit_temp(struct thermal_zone_device *tz,
>> + unsigned long *temp)
>> +{
>> + struct rockchip_thermal_data *data = tz->devdata;
>> +
>> + *temp = data->temp_critical;
>> + return 0;
>> +}
>> +
>> +static int rockchip_get_trip_temp(struct thermal_zone_device *tz, int trip,
>> + unsigned long *temp)
>> +{
>> + struct rockchip_thermal_data *data = tz->devdata;
>> +
>> + *temp = (trip == ROCKCHIP_TRIP_PASSIVE) ? data->temp_passive :
>> + data->temp_critical;
>> + return 0;
>> +}
>> +
>> +static int rockchip_set_trip_temp(struct thermal_zone_device *tz, int trip,
>> + unsigned long temp)
>> +{
>> + struct rockchip_thermal_data *data = tz->devdata;
>> +
>> + if (trip == ROCKCHIP_TRIP_CRITICAL)
>> + return -EPERM;
>> +
>> + data->temp_passive = temp;
>> + rockchip_set_alarm_temp(data, temp);
>> + return 0;
>> +}
>> +
>> +static int rockchip_bind(struct thermal_zone_device *tz,
>> + struct thermal_cooling_device *cdev)
>> +{
>> + int ret;
>> +
>> + ret = thermal_zone_bind_cooling_device(tz, ROCKCHIP_TRIP_PASSIVE, cdev,
>> + THERMAL_NO_LIMIT,
>> + THERMAL_NO_LIMIT);
>> + if (ret) {
>> + dev_err(&tz->device, "binding zone %s with cdev %s failed:%d\n",
>> + tz->type, cdev->type, ret);
>> + return ret;
>> + }
>> + return 0;
>> +}
>> +
>> +static int rockchip_unbind(struct thermal_zone_device *tz,
>> + struct thermal_cooling_device *cdev)
>> +{
>> + int ret;
>> +
>> + ret = thermal_zone_unbind_cooling_device(tz,
>> + ROCKCHIP_TRIP_PASSIVE, cdev);
>> + if (ret) {
>> + dev_err(&tz->device,
>> + "unbinding zone %s with cdev %s failed:%d\n", tz->type,
>> + cdev->type, ret);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static struct thermal_zone_device_ops rockchip_tz_ops = {
>> + .bind = rockchip_bind,
>> + .unbind = rockchip_unbind,
>> + .get_temp = rockchip_get_temp,
>> + .get_mode = rockchip_get_mode,
>> + .set_mode = rockchip_set_mode,
>> + .get_trip_type = rockchip_get_trip_type,
>> + .get_trip_temp = rockchip_get_trip_temp,
>> + .get_crit_temp = rockchip_get_crit_temp,
>> + .set_trip_temp = rockchip_set_trip_temp,
>> +};
>> +
>> +static irqreturn_t rockchip_thermal_alarm_irq(int irq, void *dev)
>> +{
>> + struct rockchip_thermal_data *data = dev;
>> +
>> + disable_irq_nosync(irq);
>> + data->irq_enabled = false;
>> +
>> + return IRQ_WAKE_THREAD;
> I think you want IRQF_ONESHOT instead of doing disable_irq dance (BTW I
> also do not see you enabling it in your threaded handle so I wonder how
> it worked for you).

Sorry, I will remove it. Amended as follows:

...
ret = devm_request_threaded_irq(&pdev->dev, data->irq,
NULL,
rockchip_thermal_alarm_irq_thread,
IRQF_ONESHOT,
"rockchip_thermal", data);

>> +}
>> +
>> +static irqreturn_t rockchip_thermal_alarm_irq_thread(int irq, void *dev)
>> +{
>> + struct rockchip_thermal_data *data = data;
>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>> +
>> + dev_dbg(&data->tz->device, "THERMAL ALARM: T > %lu\n",
>> + data->alarm_temp / 1000);
>> +
>> + if (p_tsadc_data->irq_en && p_tsadc_data->irq_handle)
>> + p_tsadc_data->irq_handle(data->regs);
>> +
>> + thermal_zone_device_update(data->tz);
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static int rockchip_thermal_probe(struct platform_device *pdev)
>> +{
>> + struct rockchip_thermal_data *data;
>> + const struct rockchip_tsadc_platform_data *p_tsadc_data;
>> + struct cpumask clip_cpus;
>> + struct resource *res;
>> + const struct of_device_id *match;
>> + int ret, temp;
>> +
>> + data = devm_kzalloc(&pdev->dev, sizeof(struct rockchip_thermal_data),
>> + GFP_KERNEL);
>> + if (!data)
>> + return -ENOMEM;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + data->regs = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(data->regs)) {
>> + dev_err(&pdev->dev, "Could not get tsadc source, %p\n",
>> + data->regs);
>> + return PTR_ERR(data->regs);
>> + }
>> +
>> + match = of_match_node(of_rockchip_thermal_match, pdev->dev.of_node);
>> + if (!match)
>> + return -ENXIO;
>> + data->pdata = (const struct rockchip_tsadc_platform_data *)match->data;
>> + if (!data->pdata)
>> + return -EINVAL;
>> + p_tsadc_data = data->pdata;
>> +
>> + data->tsadc_clk = devm_clk_get(&pdev->dev, "tsadc_clk");
>> + if (IS_ERR(data->tsadc_clk)) {
>> + dev_err(&pdev->dev, "failed to get tsadc clock\n");
>> + return PTR_ERR(data->tsadc_clk);
>> + }
> Throw in a blank line here please.

OK.

>> + ret = clk_prepare_enable(data->tsadc_clk);
>> + if (ret)
>> + return ret;
>> +
>> + data->tsadc_pclk = devm_clk_get(&pdev->dev, "tsadc_pclk");
>> + if (IS_ERR(data->tsadc_pclk)) {
>> + dev_err(&pdev->dev, "failed to get tsadc pclk\n");
>> + return PTR_ERR(data->tsadc_pclk);
>> + }
> And here too.
>

OK.

>> + ret = clk_prepare_enable(data->tsadc_pclk);
>> + if (ret)
>> + return ret;
>> +
>> + platform_set_drvdata(pdev, data);
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "passive-temp", &temp)) {
>> + dev_warn(&pdev->dev,
>> + "Missing default passive temp property in the DT.\n");
>> + data->temp_passive = p_tsadc_data->temp_passive;
>> + } else {
>> + data->temp_passive = temp;
>> + }
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "critical-temp", &temp)) {
>> + dev_warn(&pdev->dev,
>> + "Missing default critical temp property in the DT.\n");
>> + data->temp_critical = p_tsadc_data->temp_critical;
>> + } else {
>> + data->temp_critical = temp;
>> + }
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "force-shut-temp", &temp)) {
>> + dev_warn(&pdev->dev,
>> + "Missing default force shut down temp property in the DT.\n");
>> + data->temp_force_shut = p_tsadc_data->temp_force_shut;
>> + } else {
>> + data->temp_force_shut = temp;
>> + }
>> +
>> + cpumask_set_cpu(0, &clip_cpus);
>> + data->cdev = of_cpufreq_cooling_register(pdev->dev.of_node, &clip_cpus);
>> + if (IS_ERR(data->cdev)) {
>> + ret = PTR_ERR(data->cdev);
>> + dev_err(&pdev->dev,
>> + "failed to register cpufreq cooling device: %d\n", ret);
> Don't you need to disable clocks here? Disbale operation is not devm
> controlled as far as I know.
Oh, you are right!

As you say, maybe I willl fix it, as the following:

clk_disable_unprepare(data->tsadc_clk);
clk_disable_unprepare(data->tsadc_pclk);

>
>> + return ret;
>> + }
>> +
>> + data->tz = thermal_zone_device_register("rockchip_thermal",
>> + ROCKCHIP_TRIP_NUM,
>> + 0, data,
>> + &rockchip_tz_ops, NULL,
>> + p_tsadc_data->passive_delay,
>> + p_tsadc_data->polling_delay);
>> +
>> + if (IS_ERR(data->tz)) {
>> + ret = PTR_ERR(data->tz);
>> + dev_err(&pdev->dev,
>> + "failed to register thermal zone device %d\n", ret);
>> + cpufreq_cooling_unregister(data->cdev);
>> + return ret;
>> + }
>> +
>> + if (p_tsadc_data->irq_en) {
>> + data->irq = platform_get_irq(pdev, 0);
>> + if (data->irq < 0)
> You are leaking thermal and colling device here.
>

As follows:

if (p_tsadc_data->irq_en) {
data->irq = platform_get_irq(pdev, 0);
if (data->irq < 0) {
+ thermal_zone_device_unregister(data->tz);
+ cpufreq_cooling_unregister(data->cdev);
return data->irq;
}
>> + return data->irq;
>> +
>> + ret = devm_request_threaded_irq(&pdev->dev, data->irq,
>> + rockchip_thermal_alarm_irq,
>> + rockchip_thermal_alarm_irq_thread,
>> + 0, "rockchip_thermal", data);
>> + if (ret < 0) {
>> + dev_err(&pdev->dev,
>> + "failed to request tsadc irq: %d\n", ret);
> And here as well.

As follows:

if (ret < 0) {
+ thermal_zone_device_unregister(data->tz);
+ cpufreq_cooling_unregister(data->cdev);
dev_err(&pdev->dev,
"failed to request tsadc irq: %d\n", ret);
return ret;
}
>
>> + return ret;
>> + }
>> + }
>> +
>> + rockchip_thermal_initialize(data);
>> + rockchip_thermal_control(data, true);
>> + return 0;
>> +}
>> +
>> +static int rockchip_thermal_remove(struct platform_device *pdev)
>> +{
>> + struct rockchip_thermal_data *data = platform_get_drvdata(pdev);
>> +
>> + rockchip_thermal_control(data, false);
>> +
>> + thermal_zone_device_unregister(data->tz);
>> +
>> + if (!IS_ERR(data->tsadc_clk))
>> + clk_disable_unprepare(data->tsadc_clk);
> No need to check IS_ERR() here: you abort probe if you fail to obtain
> clocks.
>
OK, I will remove it.

>> +
>> + if (!IS_ERR(data->tsadc_pclk))
>> + clk_disable_unprepare(data->tsadc_pclk);
> Same here.

Ditto.

>> +
>> + cpufreq_cooling_unregister(data->cdev);
> As I mentioned I believe you should unregister cooling device before
> disabling clocks.

OK.

>> + return 0;
>> +}
>> +
>> +#ifdef CONFIG_PM_SLEEP
>> +static int rockchip_thermal_suspend(struct device *dev)
>> +{
>> + struct platform_device *pdev = to_platform_device(dev);
>> + struct rockchip_thermal_data *data = platform_get_drvdata(pdev);
>> +
>> + rockchip_thermal_control(data, false);
>> + return 0;
>> +}
>> +
>> +static int rockchip_thermal_resume(struct device *dev)
>> +{
>> + struct platform_device *pdev = to_platform_device(dev);
>> + struct rockchip_thermal_data *data = platform_get_drvdata(pdev);
>> +
>> + rockchip_thermal_initialize(data);
>> + rockchip_thermal_control(data, true);
>> +
>> + return 0;
>> +}
>> +#endif
>> +
>> +static SIMPLE_DEV_PM_OPS(rockchip_thermal_pm_ops,
>> + rockchip_thermal_suspend, rockchip_thermal_resume);
>> +
>> +static struct platform_driver rockchip_thermal_driver = {
>> + .driver = {
>> + .name = "rockchip-thermal",
>> + .owner = THIS_MODULE,
>> + .pm = &rockchip_thermal_pm_ops,
>> + .of_match_table = of_rockchip_thermal_match,
>> + },
>> + .probe = rockchip_thermal_probe,
>> + .remove = rockchip_thermal_remove,
>> +};
>> +
>> +module_platform_driver(rockchip_thermal_driver);
>> +
>> +MODULE_DESCRIPTION("ROCKCHIP THERMAL Driver");
>> +MODULE_AUTHOR("Rockchip, Inc.");
>> +MODULE_LICENSE("GPL");
>> +MODULE_ALIAS("platform:rockchip-thermal");
> Thanks.
>

Thanks for your comments.

I will amend the about and sent patch v3 today if have no other problems.

--
Best regards,
Caesar


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2014-08-27 19:41    [W:0.156 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site