lkml.org 
[lkml]   [2014]   [Jul]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v9 3/7] ata: libahci: allow to use multiple PHYs
Hello,

On Tue, Jul 08, 2014 at 09:40:00AM -0400, Tejun Heo wrote:
> (Cc'ing Hans.)
>
> On Mon, Jul 07, 2014 at 12:16:09PM +0200, Antoine Ténart wrote:
> > @@ -482,6 +482,13 @@ void ahci_save_initial_config(struct device *dev,
> > port_map &= mask_port_map;
> > }
> >
> > + /*
> > + * If port_map was filled automatically when finding port sub-nodes,
> > + * make sure we get the right set here.
> > + */
> > + if (hpriv->port_map)
> > + port_map &= hpriv->port_map;
> > +
>
> So, hpriv->port is both input and output? This is messy and can lead
> to confusing failures and there now are multiple ways to modify
> port_map. If carrying this information through ahci_host_priv is
> necessary, let's remove the direct params and introduce new input
> fields to the struct.

We just use hpriv->port_map to check port_map is valid and describes
available ports there.

hpriv->port_map is filed by the generic ahci_platform_get_resources()
function when using the new bindings and not by the drivers. port_map is
the input from the drivers.

>
> > /**
> > + * ahci_platform_enable_phys - Enable PHYs
> > + * @hpriv: host private area to store config values
> > + *
> > + * This function enables all the PHYs found in hpriv->phys, if any.
> > + * If a PHY fails to be enabled, it disables all the PHYs already
> > + * enabled in reverse order and returns an error.
> > + *
> > + * RETURNS:
> > + * 0 on success otherwise a negative error code
> > + */
> > +int ahci_platform_enable_phys(struct ahci_host_priv *hpriv)
> > +{
> > + int i, rc = 0;
> > +
> > + for (i = 0; i < hpriv->nphys; i++) {
> > + rc = phy_init(hpriv->phys[i]);
> > + if (rc)
> > + goto disable_phys;
> > +
> > + rc = phy_power_on(hpriv->phys[i]);
> > + if (rc) {
> > + phy_exit(hpriv->phys[i]);
> > + goto disable_phys;
> > + }
> > + }
> > +
> > + return 0;
> > +
> > +disable_phys:
> > + while (--i >= 0) {
> > + phy_power_off(hpriv->phys[i]);
> > + phy_exit(hpriv->phys[i]);
> > + }
> > + return rc;
> > +}
> > +EXPORT_SYMBOL_GPL(ahci_platform_enable_phys);
>
> Do we need to make hpriv->phys[] dynamically allocated? We already
> have hpriv->clks[AHCI_MAX_CLKS] and it's unlikely that we're gonna
> need more than several phys per host. Let's go with a simpler fixed
> array.
>

Well, a had a review a week ago about in the PHY driver saying I should
avoid using fixed sized arrays... And it was in a driver were we know
the maximum number of PHY available.

I think in this case were the number of PHYs depends on the h/w, we should
use a dynamically allocated array.


Antoine

--
Antoine Ténart, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2014-07-08 19:41    [W:0.091 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site