lkml.org 
[lkml]   [2014]   [Jul]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/3] ARM: dts: sti: Add st-dwc3 devicetree bindings documentation
Date
This patch documents the device tree documentation required for
the ST usb3 controller glue layer found in STiH407 devices.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
Documentation/devicetree/bindings/usb/dwc3-st.txt | 58 +++++++++++++++++++++++
1 file changed, 58 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/dwc3-st.txt

diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt
new file mode 100644
index 0000000..f14e5da
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt
@@ -0,0 +1,58 @@
+ST DWC3 glue logic
+
+This file documents the parameters for the dwc3-st driver.
+This driver provides the glue logic to use the dwc3 on STiH407 based platforms.
+
+Required properties:
+ - compatible : must be "st,stih407-dwc3"
+ - reg : glue logic base address and USB syscfg ctrl register offest
+ - reg-names : Should be "reg-glue" and "syscfg-reg".
+ - st,syscon : should be phandle to system configuration node which
+ encompases the glue registers.
+ - resets : phandle pointing to the system powerdown controller
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+ with 'reg' property.
+
+ - pinctl-names : A pinctrl state named "default" must be defined.
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt.
+
+ - pinctrl-0 : Pin control group
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt.
+
+ - ranges: allows valid 1:1 translation between child's address space and
+ parent's address space.
+
+Optional properties:
+ - st,dwc3-drd-device: to program the HC as "device" (static setup)
+
+Sub-nodes:
+The dwc3 core should be added as subnode to ST DWC3 glue as shown in the
+example below. The DT binding details of dwc3 can be found in:
+Documentation/devicetree/bindings/usb/dwc3.txt
+
+Example:
+
+st_dwc3: dwc3@8f94000 {
+ status = "disabled";
+ compatible = "st,stih407-dwc3";
+ reg = <0x08f94000 0x1000>, <0x110 0x4>;
+ reg-names = "reg-glue", "syscfg-reg";
+ st,syscfg = <&syscfg_core>;
+ resets = <&powerdown STIH407_USB3_POWERDOWN>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb3>;
+ ranges;
+
+ dwc3: dwc3@9900000 {
+ compatible = "synopsys,dwc3";
+ reg = <0x09900000 0x100000>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>;
+
+ usb-phy = <&usb2_phy>, <&usb3_phy>;
+ };
+};
--
1.9.1


\
 
 \ /
  Last update: 2014-07-04 16:01    [W:0.094 / U:2.548 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site