lkml.org 
[lkml]   [2014]   [Jul]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v6 08/23] mfd: max77686: Add Dynamic Voltage Scaling (DVS) support
From
Date
On pią, 2014-07-04 at 11:55 +0200, Javier Martinez Canillas wrote:
> Some regulators on the MAX77686 PMIC have Dynamic Voltage Scaling
> (DVS) support that allows output voltage to change dynamically.
>
> For MAX77686, these regulators are Buck regulators 2, 3 and 4.
>
> Each Buck output voltage is selected using a set of external
> inputs: DVS1-3 and SELB2-4.
>
> DVS registers can be used to configure the output voltages for each
> Buck regulator and which one is active is controled by DVSx lines.
>
> SELBx lines are used to control if individual Buck lines are ON or OFF.
>
> This patch adds support to configure the DVSx and SELBx lines
> from DT and to setup and read the GPIO lines connected to them.
>
> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
> ---
> drivers/mfd/max77686.c | 115 +++++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/max77686.h | 18 ++++---
> 2 files changed, 125 insertions(+), 8 deletions(-)

One minor comment below, but overall looks good to me:
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>


> diff --git a/drivers/mfd/max77686.c b/drivers/mfd/max77686.c
> index 8650832..648d564 100644
> --- a/drivers/mfd/max77686.c
> +++ b/drivers/mfd/max77686.c
> @@ -32,8 +32,10 @@
> #include <linux/mfd/core.h>
> #include <linux/mfd/max77686.h>
> #include <linux/mfd/max77686-private.h>
> +#include <linux/gpio/consumer.h>
> #include <linux/err.h>
> #include <linux/of.h>
> +#include <linux/export.h>
>
> #define I2C_ADDR_RTC (0x0C >> 1)
>
> @@ -101,9 +103,115 @@ static const struct of_device_id max77686_pmic_dt_match[] = {
> {},
> };
>
> +static void max77686_dt_parse_dvs_gpio(struct device *dev)
> +{
> + struct max77686_platform_data *pd = dev_get_platdata(dev);
> + int i;
> +
> + /*
> + * NOTE: we don't consider GPIO errors fatal; board may have some lines
> + * directly pulled high or low and thus doesn't specify them.
> + */
> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_dvs); i++)
> + pd->buck_gpio_dvs[i] =
> + devm_gpiod_get_index(dev, "max77686,pmic-buck-dvs", i);
> +
> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++)
> + pd->buck_gpio_selb[i] =
> + devm_gpiod_get_index(dev, "max77686,pmic-buck-selb", i);
> +}
> +
> +/**
> + * max77686_setup_gpios - init DVS-related GPIOs
> + *
> + * This function claims / initalizations GPIOs related to DVS if they are
> + * defined. This may have the effect of switching voltages if the
> + * pdata->buck_default_idx does not match the boot time state of pins.
> + */
> +int max77686_setup_gpios(struct device *dev)
> +{
> + struct max77686_platform_data *pd = dev_get_platdata(dev);
> + int buck_default_idx = pd->buck_default_idx;
> + int ret;
> + int i;
> +
> + /* Set all SELB high to avoid glitching while DVS is changing */
> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++) {
> + struct gpio_desc *gpio = pd->buck_gpio_selb[i];
> +
> + /* OK if some GPIOs aren't defined */
> + if (IS_ERR(gpio))
> + continue;
> +
> + ret = gpiod_direction_output_raw(gpio, 1);
> + if (ret) {
> + dev_err(dev, "can't set gpio[%d] dir: %d\n", i, ret);
> + return ret;
> + }
> + }
> +
> + /* Set our initial setting */
> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_dvs); i++) {
> + struct gpio_desc *gpio = pd->buck_gpio_dvs[i];
> +
> + /* OK if some GPIOs aren't defined */
> + if (IS_ERR(gpio))
> + continue;
> +
> + /* If a GPIO is valid, set it */
> + gpiod_direction_output(gpio, (buck_default_idx >> i) & 1);
> + if (ret) {
> + dev_err(dev, "can't set gpio[%d]: dir %d\n", i, ret);
> + return ret;
> + }
> + }
> +
> + /* Now set SELB low to take effect */
> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++) {
> + struct gpio_desc *gpio = pd->buck_gpio_selb[i];
> +
> + if (!IS_ERR(gpio))
> + gpiod_set_value(gpio, 0);
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(max77686_setup_gpios);
> +
> +/**
> + * max77686_read_gpios - read the current state of the dvs GPIOs
> + *
> + * We call this function at bootup to detect what slot the firmware was
> + * using for the DVS GPIOs. That way we can properly preserve the firmware's
> + * voltage settings
> + */
> +int max77686_read_gpios(struct max77686_platform_data *pdata)
> +{

Can you document that this function can sleep? It is quite obvious but
the function is exported so maybe it is worth noting.

Best regards,
Krzysztof



--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2014-07-04 13:41    [W:0.107 / U:3.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site