lkml.org 
[lkml]   [2014]   [Jul]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 9/14] input: cyapa: add gen3 trackpad device read firmware image function support
Date
Add read firmware image function supported for gen3 trackpad device,
which its function is supplied through cyapa core read_fw interface.
TEST=test on Chromebooks.

Signed-off-by: Dudley Du <dudl@cypress.com>
---
drivers/input/mouse/cyapa_gen3.c | 73 ++++++++++++++++++++++++++++++++++++++
1 file changed, 73 insertions(+)

diff --git a/drivers/input/mouse/cyapa_gen3.c b/drivers/input/mouse/cyapa_gen3.c
index 2236706..7e9fe09 100644
--- a/drivers/input/mouse/cyapa_gen3.c
+++ b/drivers/input/mouse/cyapa_gen3.c
@@ -696,6 +696,36 @@ static int cyapa_gen3_write_fw_block(struct cyapa *cyapa,
return ret;
}

+/*
+ * A firmware block read command reads 16 bytes of data from flash starting
+ * from a given address. The 12-byte block read command has the format:
+ * <0xff> <CMD> <Key> <Addr>
+ *
+ * <0xff> - every command starts with 0xff
+ * <CMD> - the read command value is 0x3c
+ * <Key> - read commands include an 8-byte key: { 00 01 02 03 04 05 06 07 }
+ * <Addr> - Memory address (16-bit, big-endian)
+ *
+ * The command is followed by an i2c block read to read the 16 bytes of data.
+ */
+static int cyapa_gen3_read_fw_bytes(struct cyapa *cyapa, u16 addr, u8 *data)
+{
+ int ret;
+ u8 cmd[] = { 0xff, 0x3c, 0x00, 0x01, 0x02, 0x03, 0x04,
+ 0x05, 0x06, 0x07, addr >> 8, addr };
+
+ ret = cyapa_gen3_write_buffer(cyapa, cmd, sizeof(cmd));
+ if (ret)
+ return ret;
+
+ /* read data buffer starting from offset 16 */
+ ret = cyapa_i2c_reg_read_block(cyapa, 16, CYAPA_FW_READ_SIZE, data);
+ if (ret != CYAPA_FW_READ_SIZE)
+ return (ret < 0) ? ret : -EIO;
+
+ return 0;
+}
+
static int cyapa_gen3_write_blocks(struct cyapa *cyapa,
size_t start_block, size_t block_count,
const u8 *image_data)
@@ -742,6 +772,47 @@ static int cyapa_gen3_do_fw_update(struct cyapa *cyapa,
return 0;
}

+/*
+ * Read the entire firmware image into ->fw_image.
+ * If the ->fw_image has already been allocated, then this function
+ * doesn't do anything and just returns 0.
+ * If an error occurs while reading the image, ->fw_image is freed, and
+ * the error is returned.
+ *
+ * The firmware is a fixed size (CYAPA_FW_SIZE), and is read out in
+ * fixed length (CYAPA_FW_READ_SIZE) chunks.
+ */
+static int cyapa_gen3_read_fw(struct cyapa *cyapa)
+{
+ int ret;
+ int addr;
+
+ ret = cyapa_gen3_bl_enter(cyapa);
+ if (ret)
+ goto err;
+
+ cyapa->fw_image = kmalloc(CYAPA_FW_SIZE, GFP_KERNEL);
+ if (!cyapa->fw_image) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ for (addr = 0; addr < CYAPA_FW_SIZE; addr += CYAPA_FW_READ_SIZE) {
+ ret = cyapa_gen3_read_fw_bytes(cyapa, CYAPA_FW_HDR_START + addr,
+ &cyapa->fw_image[addr]);
+ if (ret) {
+ kfree(cyapa->fw_image);
+ cyapa->fw_image = NULL;
+ break;
+ }
+ }
+
+err:
+ if (cyapa->fw_image)
+ cyapa->fw_image_size = CYAPA_FW_SIZE;
+ return ret;
+}
+
static ssize_t cyapa_gen3_do_calibrate(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
@@ -1134,6 +1205,8 @@ const struct cyapa_dev_ops cyapa_gen3_ops = {
.show_baseline = cyapa_gen3_show_baseline,
.calibrate_store = cyapa_gen3_do_calibrate,

+ .read_fw = cyapa_gen3_read_fw,
+
.state_parse = cyapa_gen3_state_parse,
.operational_check = cyapa_gen3_do_operational_check,

--
1.7.9.5

This message and any attachments may contain Cypress (or its subsidiaries) confidential information. If it has been received in error, please advise the sender and immediately delete this message.
[unhandled content-type:application/ms-tnef]
\
 
 \ /
  Last update: 2014-07-04 13:41    [W:0.038 / U:46.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site