lkml.org 
[lkml]   [2014]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/5] tty: serial: 8250 core: add runtime pm
Hi,

On Wed, Jul 16, 2014 at 05:54:56PM +0200, Sebastian Andrzej Siewior wrote:
> On 07/16/2014 05:16 PM, Felipe Balbi wrote:
> > Hi,
>
> Hi Felipe,
>
> > On Wed, Jul 16, 2014 at 04:45:02PM +0200, Sebastian Andrzej Siewior
> > wrote:
> >> @@ -1280,6 +1285,7 @@ static void serial8250_stop_tx(struct
> >> uart_port *port) struct uart_8250_port *up = container_of(port,
> >> struct uart_8250_port, port);
> >>
> >> + pm_runtime_get_sync(port->dev); __stop_tx(up);
> >>
> >> /* @@ -1289,6 +1295,8 @@ static void serial8250_stop_tx(struct
> >> uart_port *port) up->acr |= UART_ACR_TXDIS; serial_icr_write(up,
> >> UART_ACR, up->acr); } + pm_runtime_mark_last_busy(port->dev); +
> >> pm_runtime_put_autosuspend(port->dev); }
> >>
> >> static void serial8250_start_tx(struct uart_port *port) @@
> >> -1296,8 +1304,9 @@ static void serial8250_start_tx(struct
> >> uart_port *port) struct uart_8250_port *up = container_of(port,
> >> struct uart_8250_port, port);
> >>
> >> + pm_runtime_get_sync(port->dev); if (up->dma &&
> >> !serial8250_tx_dma(up)) { - return; + goto out; } else if
> >> (!(up->ier & UART_IER_THRI)) { up->ier |= UART_IER_THRI;
> >> serial_port_out(port, UART_IER, up->ier); @@ -1318,6 +1327,9 @@
> >> static void serial8250_start_tx(struct uart_port *port) up->acr
> >> &= ~UART_ACR_TXDIS; serial_icr_write(up, UART_ACR, up->acr); }
> >> +out: + pm_runtime_mark_last_busy(port->dev); +
> >> pm_runtime_put_autosuspend(port->dev);
> >
> > I wonder if you should get_sync() on start_tx() and only
> > put_autosuspend() at stop_tx(). I guess the outcome would be
> > largely the same, no ?
>
> I just opened minicom on ttyS0 and gave a try. start_tx() was invoked
> each time I pressed a key (sent a character). I haven't seen stop_tx()
> even after after I closed minicom. I guess stop_tx() is invoked if you
> switch half-duplex communication.

that's bad, I expected stop to be called also after each character.

> > well, other than in probe and other functions which need to make
> > sure clocks are on, but it seems unnecessary to enable/disable in
> > every function.
>
> What do you have in mind? Do you plan to let the uart on while the
> minicom is attached but is doing nothing? In that case, ->startup() and
> ->shutdown() should be enough.

no the idea was to keep it on for as long as it's transferring
characters and idle it otherwise, if that can't be done easily, then I
guess your way is the only way.

> If you want to put the uart off while the port is open but idle then
> you should cover the callbacks as they are independent of each other.
> You could receive three ->set_termios() even without a single
> ->start_tx(). And as far as I understand the whole situation, you need
> to make sure the UART is "up" while you touch a single register not
> only sending characters, right?

right, for those cases, you have to get/put around function entry/exit;
I was just assuming that we didn't have to do that for each and every
callback.

cheers

--
balbi
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2014-07-16 18:41    [W:0.171 / U:0.316 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site