lkml.org 
[lkml]   [2014]   [Jul]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH 2/3] regulator: s2mpa01: Optimize the regulator description macro
From
On Mon, Jul 14, 2014 at 2:19 PM, Krzysztof Kozlowski
<k.kozlowski@samsung.com> wrote:
> On 08.07.2014 14:27, Amit Daniel Kachhap wrote:
>>
>> This patch makes the regulator description macro take minimum and
>> steps voltage as parameter. In this way many repeated macros can be
>> removed. Now these macros are repeated only if the the LDO/BUCK ctrl
>> registers have non-linear positions. The good thing is these ctrl
>> registers
>> are mostly linear so they are not passed as parameters.
>>
>> This patch reduces the code size and also allow easy addition of more
>> s2mpxxx PMIC drivers which differs a lot in minimum/step voltages.
>>
>> Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
>> ---
>> drivers/regulator/s2mpa01.c | 136
>> ++++++++++++--------------------------------
>> 1 file changed, 37 insertions(+), 99 deletions(-)
>>
>> diff --git a/drivers/regulator/s2mpa01.c b/drivers/regulator/s2mpa01.c
>> index 962c5f1..8073466 100644
>> --- a/drivers/regulator/s2mpa01.c
>> +++ b/drivers/regulator/s2mpa01.c
>> @@ -235,28 +235,14 @@ static struct regulator_ops s2mpa01_buck_ops = {
>> .set_ramp_delay = s2mpa01_set_ramp_delay,
>> };
>>
>> -#define regulator_desc_ldo1(num) { \
>> +#define regulator_desc_ldo(num, min, step) { \
>
>
> Why adding parameter for the 'min' value? It is always the same for LDOs -
> 800 mV.
>
> The same applies for the s2mps11 regulator driver.
Correct. min parameter can be removed.
Thanks for the review.
>
> Best regards,
> Krzysztof
>
>
>> .name = "LDO"#num, \
>> .id = S2MPA01_LDO##num, \
>> .ops = &s2mpa01_ldo_ops, \
>> .type = REGULATOR_VOLTAGE, \
>> .owner = THIS_MODULE, \
>> - .min_uV = MIN_800_MV, \
>> - .uV_step = STEP_50_MV, \
>> - .n_voltages = S2MPA01_LDO_N_VOLTAGES, \
>> - .vsel_reg = S2MPA01_REG_L1CTRL + num - 1, \
>> - .vsel_mask = S2MPA01_LDO_VSEL_MASK, \
>> - .enable_reg = S2MPA01_REG_L1CTRL + num - 1, \
>> - .enable_mask = S2MPA01_ENABLE_MASK \
>> -}
>> -#define regulator_desc_ldo2(num) { \
>> - .name = "LDO"#num, \
>> - .id = S2MPA01_LDO##num, \
>> - .ops = &s2mpa01_ldo_ops, \
>> - .type = REGULATOR_VOLTAGE, \
>> - .owner = THIS_MODULE, \
>> - .min_uV = MIN_800_MV, \
>> - .uV_step = STEP_25_MV, \
>> + .min_uV = min, \
>> + .uV_step = step, \
>> .n_voltages = S2MPA01_LDO_N_VOLTAGES, \
>> .vsel_reg = S2MPA01_REG_L1CTRL + num - 1, \
>> .vsel_mask = S2MPA01_LDO_VSEL_MASK, \
>> @@ -296,14 +282,14 @@ static struct regulator_ops s2mpa01_buck_ops = {
>> .enable_mask = S2MPA01_ENABLE_MASK \
>> }
>>
>> -#define regulator_desc_buck6_7(num) { \
>> +#define regulator_desc_buck6_10(num, min, step) { \
>> .name = "BUCK"#num, \
>> .id = S2MPA01_BUCK##num, \
>> .ops = &s2mpa01_buck_ops, \
>> .type = REGULATOR_VOLTAGE, \
>> .owner = THIS_MODULE, \
>> - .min_uV = MIN_600_MV, \
>> - .uV_step = STEP_6_25_MV, \
>> + .min_uV = min, \
>> + .uV_step = step, \
>> .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \
>> .ramp_delay = S2MPA01_RAMP_DELAY, \
>> .vsel_reg = S2MPA01_REG_B6CTRL2 + (num - 6) * 2, \
>> @@ -312,91 +298,43 @@ static struct regulator_ops s2mpa01_buck_ops = {
>> .enable_mask = S2MPA01_ENABLE_MASK \
>> }
>>
>> -#define regulator_desc_buck8 { \
>> - .name = "BUCK8", \
>> - .id = S2MPA01_BUCK8, \
>> - .ops = &s2mpa01_buck_ops, \
>> - .type = REGULATOR_VOLTAGE, \
>> - .owner = THIS_MODULE, \
>> - .min_uV = MIN_800_MV, \
>> - .uV_step = STEP_12_5_MV, \
>> - .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \
>> - .ramp_delay = S2MPA01_RAMP_DELAY, \
>> - .vsel_reg = S2MPA01_REG_B8CTRL2, \
>> - .vsel_mask = S2MPA01_BUCK_VSEL_MASK, \
>> - .enable_reg = S2MPA01_REG_B8CTRL1, \
>> - .enable_mask = S2MPA01_ENABLE_MASK \
>> -}
>> -
>> -#define regulator_desc_buck9 { \
>> - .name = "BUCK9", \
>> - .id = S2MPA01_BUCK9, \
>> - .ops = &s2mpa01_buck_ops, \
>> - .type = REGULATOR_VOLTAGE, \
>> - .owner = THIS_MODULE, \
>> - .min_uV = MIN_1500_MV, \
>> - .uV_step = STEP_12_5_MV, \
>> - .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \
>> - .ramp_delay = S2MPA01_RAMP_DELAY, \
>> - .vsel_reg = S2MPA01_REG_B9CTRL2, \
>> - .vsel_mask = S2MPA01_BUCK_VSEL_MASK, \
>> - .enable_reg = S2MPA01_REG_B9CTRL1, \
>> - .enable_mask = S2MPA01_ENABLE_MASK \
>> -}
>> -
>> -#define regulator_desc_buck10 { \
>> - .name = "BUCK10", \
>> - .id = S2MPA01_BUCK10, \
>> - .ops = &s2mpa01_buck_ops, \
>> - .type = REGULATOR_VOLTAGE, \
>> - .owner = THIS_MODULE, \
>> - .min_uV = MIN_1000_MV, \
>> - .uV_step = STEP_12_5_MV, \
>> - .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \
>> - .ramp_delay = S2MPA01_RAMP_DELAY, \
>> - .vsel_reg = S2MPA01_REG_B10CTRL2, \
>> - .vsel_mask = S2MPA01_BUCK_VSEL_MASK, \
>> - .enable_reg = S2MPA01_REG_B10CTRL1, \
>> - .enable_mask = S2MPA01_ENABLE_MASK \
>> -}
>> -
>> static struct regulator_desc regulators[] = {
>> - regulator_desc_ldo2(1),
>> - regulator_desc_ldo1(2),
>> - regulator_desc_ldo1(3),
>> - regulator_desc_ldo1(4),
>> - regulator_desc_ldo1(5),
>> - regulator_desc_ldo2(6),
>> - regulator_desc_ldo1(7),
>> - regulator_desc_ldo1(8),
>> - regulator_desc_ldo1(9),
>> - regulator_desc_ldo1(10),
>> - regulator_desc_ldo2(11),
>> - regulator_desc_ldo1(12),
>> - regulator_desc_ldo1(13),
>> - regulator_desc_ldo1(14),
>> - regulator_desc_ldo1(15),
>> - regulator_desc_ldo1(16),
>> - regulator_desc_ldo1(17),
>> - regulator_desc_ldo1(18),
>> - regulator_desc_ldo1(19),
>> - regulator_desc_ldo1(20),
>> - regulator_desc_ldo1(21),
>> - regulator_desc_ldo2(22),
>> - regulator_desc_ldo2(23),
>> - regulator_desc_ldo1(24),
>> - regulator_desc_ldo1(25),
>> - regulator_desc_ldo1(26),
>> + regulator_desc_ldo(1, MIN_800_MV, STEP_25_MV),
>> + regulator_desc_ldo(2, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(3, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(4, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(5, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(6, MIN_800_MV, STEP_25_MV),
>> + regulator_desc_ldo(7, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(8, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(9, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(10, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(11, MIN_800_MV, STEP_25_MV),
>> + regulator_desc_ldo(12, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(13, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(14, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(15, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(16, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(17, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(18, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(19, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(20, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(21, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(22, MIN_800_MV, STEP_25_MV),
>> + regulator_desc_ldo(23, MIN_800_MV, STEP_25_MV),
>> + regulator_desc_ldo(24, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(25, MIN_800_MV, STEP_50_MV),
>> + regulator_desc_ldo(26, MIN_800_MV, STEP_50_MV),
>> regulator_desc_buck1_4(1),
>> regulator_desc_buck1_4(2),
>> regulator_desc_buck1_4(3),
>> regulator_desc_buck1_4(4),
>> regulator_desc_buck5,
>> - regulator_desc_buck6_7(6),
>> - regulator_desc_buck6_7(7),
>> - regulator_desc_buck8,
>> - regulator_desc_buck9,
>> - regulator_desc_buck10,
>> + regulator_desc_buck6_10(6, MIN_600_MV, STEP_6_25_MV),
>> + regulator_desc_buck6_10(7, MIN_600_MV, STEP_6_25_MV),
>> + regulator_desc_buck6_10(8, MIN_800_MV, STEP_12_5_MV),
>> + regulator_desc_buck6_10(9, MIN_1500_MV, STEP_12_5_MV),
>> + regulator_desc_buck6_10(10, MIN_1000_MV, STEP_12_5_MV),
>> };
>>
>> static int s2mpa01_pmic_probe(struct platform_device *pdev)
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/


\
 
 \ /
  Last update: 2014-07-15 14:21    [W:0.079 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site