lkml.org 
[lkml]   [2014]   [Jun]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRE: [PATCH V3] regulator: DA9211 : new regulator driver
> -----Original Message-----
> From: Mark Brown [mailto:broonie@kernel.org]
> Sent: Saturday, June 28, 2014 12:01 AM
> To: Opensource [James Seong-Won Ban]
> Cc: Liam Girdwood; Support Opensource; LKML; David Dajun Chen
> Subject: Re: [PATCH V3] regulator: DA9211 : new regulator driver
>
> On Mon, Jun 02, 2014 at 08:17:03AM +0100, James Ban wrote:
>
> > This is the driver for the Dialog DA9211 Multi-phase 12A DC-DC Buck
> > Converter regulator. It communicates via an I2C bus to the device.
>
> This *still* seems to have all the same problems with inconsistent handling of
> the A and B register sets
>
> > + /* Make sure to exit from suspend mode on enable */
> > + if (regulator->reg_rselect == DA9211_RSEL_NO_GPIO) {
> > + ret = regmap_update_bits(chip->regmap, info->conf.reg,
> > + info->conf.sel_mask,
> > + DA9211_VBUCKA_SEL_A);
> > + if (ret < 0)
> > + return ret;
> > + }
>
> Here it forces set A if and only if in no GPIO mode but...
>
> > +static int da9211_regulator_set_suspend_voltage(struct regulator_dev *rdev,
> > + int uV)
> > +{
> > + struct da9211_regulator *regulator = rdev_get_drvdata(rdev);
> > + struct da9211_regulator_info *info = regulator->info;
> > + struct da9211 *chip = regulator->da9211;
> > + int ret;
> > +
> > + ret = regulator_map_voltage_linear(rdev, uV, uV);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return regmap_update_bits(chip->regmap, info->volt.reg_b,
> > + info->volt.v_mask, ret);
> > +}
>
> ...this unconditionally uses set B and...
>
> > +static int da9211_suspend_enable(struct regulator_dev *rdev) {
> > + struct da9211_regulator *regulator = rdev_get_drvdata(rdev);
> > + struct da9211_regulator_info *info = regulator->info;
> > + struct da9211 *chip = regulator->da9211;
> > +
> > + /* Select register set B for voltage ramping. */
> > + if (regulator->reg_rselect == DA9211_RSEL_NO_GPIO)
> > + return regmap_update_bits(chip->regmap, info->conf.reg,
> > + info->conf.sel_mask,
> > + DA9211_VBUCKA_SEL_B);
> > + else
> > + return 0;
> > +}
>
> ...this uses B if not using a GPIO and otherwise reports success without actually
> doing anything (which seems buggy). These behaviours aren't compatible with
> each other, set_suspend_voltage() will break if set B is selected by GPIO for
> example.
>
> Please either go through and try to make these things all consistent or
> (probably better) strip out the suspend and probably GPIO handling for now, get
> the bulk of the driver merged, and then come back and try to deal with those
> tricky bits.
Though the GPIO control and suspend was introduced for more usability of user,
You seems to want more strict compatibility at any case.
As your suggestion, I will strip out the suspend and GPIO handling.


\
 
 \ /
  Last update: 2014-06-30 09:41    [W:0.033 / U:0.972 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site