lkml.org 
[lkml]   [2014]   [Jun]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 1/2] documentation: add rockchip spi documentation
Date
Am Dienstag, 24. Juni 2014, 11:18:02 schrieb Mark Rutland:
> On Tue, Jun 24, 2014 at 04:58:43AM +0100, addy ke wrote:
> > Signed-off-by: addy ke <addy.ke@rock-chips.com>
> > ---
> >
> > .../devicetree/bindings/spi/spi-rockchip.txt | 51
> > ++++++++++++++++++++++ 1 file changed, 51 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/spi/spi-rockchip.txt
> >
> > diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt
> > b/Documentation/devicetree/bindings/spi/spi-rockchip.txt new file mode
> > 100644
> > index 0000000..ce9c881
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
> > @@ -0,0 +1,51 @@
> > +* Rockchip SPI Controller
> > +
> > +The Rockchip SPI controller is used to interface with various devices
> > such as flash +and display controllers using the SPI communication
> > interface.
> > +
> > +Required SoC Specific Properties:
> > +
> > +- compatible: should be one of the following.
> > + - rockchip,rk3066-spi: for rk3066, rk3188 and rk3288 platforms.
>
> Are you sure you don't want specifc strings for rk3188 and rk3288 (in
> addtion to the common "rockchip,rk3066-spi")?

Wasn't the convention that "later" platforms that are compatible to an earlier
one, reuse this compatible string instead of introducing a new one?

From what I've heard so far, the specific spi controller got introduced with
the rk3066 [earlier SoCs used a different implementation] and didn't change for
rk3188 and rk3288. Addy may be able to verify this.


> > +- reg: physical base address of the controller and length of memory
> > mapped
> > + region.
> > +- interrupts: The interrupt number to the cpu. The interrupt specifier
> > format + depends on the interrupt controller.
> > +- clocks: Must contain an entry for each entry in clock-names.
> > +- clock-names: Shall be "spiclk" for the transfer-clock, and "apb_pclk"
> > for + the peripheral clock.
> > +
> > +Optional properties:
> > +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
> > + Documentation/devicetree/bindings/dma/dma.txt
> > +- dma-names: DMA request names should include "tx" and "rx" if present.
> > +
> > +Example:
> > +
> > +- SoC Specific Portion:
> > +
> > + spi0: spi@ff110000 {
> > + compatible = "rockchip,rockchip-spi";
>
> This does not match the description of the compatible property.
>
> > + reg = <0xff110000 0x1000>;
> > + dmas = <&pdma1 11>, <&pdma1 12>;
> > + dma-names = "tx", "rx";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
>
> These weren't mentioned.
>
> > + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0 &spi0_cs1>;
>
> pinctrl was not mentioned.
>
> > + clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
> > + clock-names = "spiclk", "apb_pclk";
> > + status = "disabled";
>
> Any reason for the status?

I guess to have the spi controller only be enabled when a board is using it as
below. But it may be an implementation detail which could be omitted from the
binding doc.


>
> > + };
> > +
> > +- Board Specific Portion:
> > +
> > + &spi0 {
> > + status = "okay";
> > + spi_test@00 {
> > + compatible = "rockchip,spi_test";
>
> Huh?

SPI declares it's devices similar to i2c, so while the example might profit
from a more casual device, I'm not exactly sure what is the problem here.


Thanks
Heiko



\
 
 \ /
  Last update: 2014-06-24 13:01    [W:0.172 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site