lkml.org 
[lkml]   [2014]   [May]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 4/4] ARM: dts: dra7: add OCP2SCP3 and SATA nodes
Tony,

On 04/23/2014 08:36 PM, Roger Quadros wrote:
> From: Balaji T K <balajitk@ti.com>
>
> Add nodes for OCP2SCP3 bus, SATA controller and SATA PHY.
>
> [Roger Q] Clean up.
>
> CC: Benoit Cousson <bcousson@baylibre.com>
> Signed-off-by: Balaji T K <balajitk@ti.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
> arch/arm/boot/dts/dra7.dtsi | 39 +++++++++++++++++++++++++++++++++++++++
> 1 file changed, 39 insertions(+)
>
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> index 1c0f8e1..084f42e 100644
> --- a/arch/arm/boot/dts/dra7.dtsi
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -789,6 +789,45 @@
> dma-names = "tx0", "rx0";
> status = "disabled";
> };
> +
> + omap_control_sata: control-phy@4a002374 {
> + compatible = "ti,control-phy-pipe3";
> + reg = <0x4a002374 0x4>;
> + reg-names = "power";
> + clocks = <&sys_clkin1>;
> + clock-names = "sysclk";
> + };
> +
> + /* OCP2SCP3 */
> + ocp2scp@4a090000 {
> + compatible = "ti,omap-ocp2scp";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + reg = <0x4a090000 0x20>;
> + ti,hwmods = "ocp2scp3";
> + sata_phy: phy@4A096000 {
> + compatible = "ti,phy-pipe3-sata";
> + reg = <0x4A096000 0x80>, /* phy_rx */
> + <0x4A096400 0x64>, /* phy_tx */
> + <0x4A096800 0x40>; /* pll_ctrl */
> + reg-names = "phy_rx", "phy_tx", "pll_ctrl";
> + ctrl-module = <&omap_control_sata>;
> + clocks = <&sys_clkin1>;
> + clock-names = "sysclk";
> + #phy-cells = <0>;
> + };
> + };
> +
> + sata: sata@4a141100 {
> + compatible = "snps,dwc-ahci";
> + reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
> + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;

This will need to be changed like so if the IRQ crossbar changes [1] go in

+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;

cheers,
-roger

[1] - http://article.gmane.org/gmane.linux.documentation/23293

> + phys = <&sata_phy>;
> + phy-names = "sata-phy";
> + clocks = <&sata_ref_clk>;
> + ti,hwmods = "sata";
> + };
> };
> };
>
>



\
 
 \ /
  Last update: 2014-05-07 10:41    [W:0.176 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site