lkml.org 
[lkml]   [2014]   [May]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 12/13] mmc: mmci: Add Qcom specific rx_fifocnt logic.
Date
From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

MCIFIFOCNT register behaviour on Qcom chips is very different than the other
pl180 integrations. MCIFIFOCNT register contains the number of
words that are still waiting to be transferred through the FIFO. It keeps
decrementing once the host CPU reads the MCIFIFO. With the existing logic and
the MCIFIFOCNT behaviour, mmci_pio_read will loop forever, as the FIFOCNT
register will always return transfer size before reading the FIFO.

Also the data sheet states that "This register is only useful for debug
purposes and should not be used for normal operation since it does not reflect
data which may or may not be in the pipeline".

This patch implements a qcom specific get_rx_fifocnt function which is
implemented based on status register flags. Based on qcom_fifo flag in
variant data structure, the corresponding get_rx_fifocnt function is selected.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
drivers/mmc/host/mmci.c | 30 ++++++++++++++++++++++++++++--
drivers/mmc/host/mmci.h | 1 +
2 files changed, 29 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 8b23368..7a11522 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -73,6 +73,7 @@ static unsigned int fmax = 515633;
* @busy_detect: true if busy detection on dat0 is supported
* @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply
* @explicit_mclk_control: enable explicit mclk control in driver.
+ * @qcom_fifo: enables qcom specific fifo pio read logic.
*/
struct variant_data {
unsigned int clkreg;
@@ -95,6 +96,7 @@ struct variant_data {
bool busy_detect;
bool pwrreg_nopower;
bool explicit_mclk_control;
+ bool qcom_fifo;
};

static struct variant_data variant_arm = {
@@ -990,15 +992,34 @@ mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
}
}

+static int mmci_get_rx_fifocnt(struct mmci_host *host, u32 status, int remain)
+{
+ return remain - (readl(host->base + MMCIFIFOCNT) << 2);
+}
+
+static int mmci_qcom_get_rx_fifocnt(struct mmci_host *host, u32 status, int r)
+{
+ /*
+ * on qcom SDCC4 only 8 words are used in each burst so only 8 addresses
+ * from the fifo range should be used
+ */
+ if (status & MCI_RXFIFOHALFFULL)
+ return host->variant->fifohalfsize;
+ else if (status & MCI_RXDATAAVLBL)
+ return 4;
+
+ return 0;
+}
+
static int mmci_pio_read(struct mmci_host *host, char *buffer, unsigned int remain)
{
void __iomem *base = host->base;
char *ptr = buffer;
- u32 status;
+ u32 status = readl(host->base + MMCISTATUS);
int host_remain = host->size;

do {
- int count = host_remain - (readl(base + MMCIFIFOCNT) << 2);
+ int count = host->get_rx_fifocnt(host, status, host_remain);

if (count > remain)
count = remain;
@@ -1488,6 +1509,11 @@ static int mmci_probe(struct amba_device *dev,
if (ret)
goto host_free;

+ if (variant->qcom_fifo)
+ host->get_rx_fifocnt = mmci_qcom_get_rx_fifocnt;
+ else
+ host->get_rx_fifocnt = mmci_get_rx_fifocnt;
+
host->plat = plat;
host->variant = variant;
host->mclk = clk_get_rate(host->clk);
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index b5f0810..5f76670 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -229,6 +229,7 @@ struct mmci_host {
/* pio stuff */
struct sg_mapping_iter sg_miter;
unsigned int size;
+ int (*get_rx_fifocnt)(struct mmci_host *h, u32 status, int remain);

#ifdef CONFIG_DMA_ENGINE
/* DMA stuff */
--
1.9.1


\
 
 \ /
  Last update: 2014-05-30 21:41    [W:0.106 / U:0.252 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site