lkml.org 
[lkml]   [2014]   [May]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] staging: comedi: ni_daq_700: add AI range and input mode switching
Date
I received a patch from the original author of the driver, Fred Brooks,
to add support for switching the input range and the
single-ended/differential input mode for the AI subdevice.

I used the patch as-is apart from minor whitespace fixes and
reformatting the changes to the driver description comment.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Fred Brooks <frederick.brooks@microchip.com>
---
drivers/staging/comedi/drivers/ni_daq_700.c | 53 +++++++++++++++++++++++------
1 file changed, 43 insertions(+), 10 deletions(-)

diff --git a/drivers/staging/comedi/drivers/ni_daq_700.c b/drivers/staging/comedi/drivers/ni_daq_700.c
index 55d80ef..e66c0b9 100644
--- a/drivers/staging/comedi/drivers/ni_daq_700.c
+++ b/drivers/staging/comedi/drivers/ni_daq_700.c
@@ -24,21 +24,30 @@
* based on ni_daq_dio24 by Daniel Vecino Castel <dvecino@able.es>
* Devices: [National Instruments] PCMCIA DAQ-Card-700 (ni_daq_700)
* Status: works
- * Updated: Wed, 19 Sep 2012 12:07:20 +0000
+ * Updated: Wed, 21 May 2014 12:07:20 +0000
*
* The daqcard-700 appears in Comedi as a digital I/O subdevice (0) with
- * 16 channels and a analog input subdevice (1) with 16 single-ended channels.
+ * 16 channels and a analog input subdevice (1) with 16 single-ended channels
+ * or 8 differential channels, and three input ranges.
*
* Digital: The channel 0 corresponds to the daqcard-700's output
* port, bit 0; channel 8 corresponds to the input port, bit 0.
*
* Digital direction configuration: channels 0-7 output, 8-15 input.
*
- * Analog: The input range is 0 to 4095 for -10 to +10 volts
+ * Analog: The input range is 0 to 4095 with a default of -10 to +10 volts.
+ * Valid ranges:
+ * 0 for -10 to 10V bipolar
+ * 1 for -5 to 5V bipolar
+ * 2 for -2.5 to 2.5V bipolar
+ *
* IRQ is assigned but not used.
*
* Version 0.1 Original DIO only driver
* Version 0.2 DIO and basic AI analog input support on 16 se channels
+ * Version 0.3 Add SE or DIFF mode and range switching +-10,+-5,+-2.5
+ * Clear the FIFO of data before the conversion to handle card
+ * mode switching glitches.
*
* Manuals: Register level: http://www.ni.com/pdf/manuals/340698.pdf
* User Manual: http://www.ni.com/pdf/manuals/320676d.pdf
@@ -68,6 +77,17 @@
#define CDA_R2 0x0A /* RW 8bit */
#define CMO_R 0x0B /* RO 8bit */
#define TIC_R 0x06 /* WO 8bit */
+/* daqcard700 modes */
+#define CMD_R3_DIFF 0x04 /* diff mode */
+
+static const struct comedi_lrange range_daq700_ai = {
+ 3,
+ {
+ BIP_RANGE(10),
+ BIP_RANGE(5),
+ BIP_RANGE(2.5)
+ }
+};

static int daq700_dio_insn_bits(struct comedi_device *dev,
struct comedi_subdevice *s,
@@ -130,20 +150,34 @@ static int daq700_ai_rinsn(struct comedi_device *dev,
struct comedi_subdevice *s,
struct comedi_insn *insn, unsigned int *data)
{
- int n, chan;
+ int n;
int d;
int ret;
+ unsigned int chan = CR_CHAN(insn->chanspec);
+ unsigned int aref = CR_AREF(insn->chanspec);
+ unsigned int range = CR_RANGE(insn->chanspec);
+ unsigned int r3_bits = 0;
+
+ /* set channel input modes */
+ if (aref == AREF_DIFF)
+ r3_bits |= CMD_R3_DIFF;
+ /* write channel mode/range */
+ if (range >= 1)
+ range++; /* convert range to hardware value */
+ outb(r3_bits | (range & 0x03), dev->iobase + CMD_R3);

- chan = CR_CHAN(insn->chanspec);
/* write channel to multiplexer */
/* set mask scan bit high to disable scanning */
- outb(chan | 0x80, dev->iobase + CMD_R1);
+ outb((chan & 0x0f) | 0x80, dev->iobase + CMD_R1);

/* convert n samples */
for (n = 0; n < insn->n; n++) {
/* trigger conversion with out0 L to H */
outb(0x00, dev->iobase + CMD_R2); /* enable ADC conversions */
outb(0x30, dev->iobase + CMO_R); /* mode 0 out0 L, from H */
+ outb(0x00, dev->iobase + ADCLEAR_R); /* clear the ADC FIFO */
+ /* read 16bit junk from FIFO to clear */
+ inw(dev->iobase + ADFIFO_R);
/* mode 1 out0 H, L to H, start conversion */
outb(0x32, dev->iobase + CMO_R);

@@ -219,11 +253,10 @@ static int daq700_auto_attach(struct comedi_device *dev,
/* DAQCard-700 ai */
s = &dev->subdevices[1];
s->type = COMEDI_SUBD_AI;
- /* we support single-ended (ground) */
- s->subdev_flags = SDF_READABLE | SDF_GROUND;
+ s->subdev_flags = SDF_READABLE | SDF_GROUND | SDF_DIFF;
s->n_chan = 16;
s->maxdata = (1 << 12) - 1;
- s->range_table = &range_bipolar10;
+ s->range_table = &range_daq700_ai;
s->insn_read = daq700_ai_rinsn;
daq700_ai_config(dev, s);

@@ -260,5 +293,5 @@ module_comedi_pcmcia_driver(daq700_driver, daq700_cs_driver);
MODULE_AUTHOR("Fred Brooks <nsaspook@nsaspook.com>");
MODULE_DESCRIPTION(
"Comedi driver for National Instruments PCMCIA DAQCard-700 DIO/AI");
-MODULE_VERSION("0.2.00");
+MODULE_VERSION("0.3.00");
MODULE_LICENSE("GPL");
--
1.9.2


\
 
 \ /
  Last update: 2014-05-29 14:01    [W:0.092 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site