lkml.org 
[lkml]   [2014]   [May]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 08/13] mmc: mmci: add edge support to data and command out in variant data.
Date
From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

This patch adds edge support for data and command out to variant structure
giving more flexibility to the driver to support more SOCs which have
different clock register layout.

Without this patch other new SOCs like Qcom will have to add more code to
special case them

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
drivers/mmc/host/mmci.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 2f4cdf3..8deea4a 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -53,6 +53,7 @@ static unsigned int fmax = 515633;
* @clkreg: default value for MCICLOCK register
* @clkreg_enable: enable value for MMCICLOCK register
* @clkreg_8bit_bus_enable: enable value for 8 bit bus
+ * @clkreg_neg_edge_enable: enable value for inverted data/cmd output
* @datalength_bits: number of bits in the MMCIDATALENGTH register
* @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY
* is asserted (likewise for RX)
@@ -74,6 +75,7 @@ struct variant_data {
unsigned int clkreg;
unsigned int clkreg_enable;
unsigned int clkreg_8bit_bus_enable;
+ unsigned int clkreg_neg_edge_enable;
unsigned int datalength_bits;
unsigned int fifosize;
unsigned int fifohalfsize;
@@ -143,6 +145,7 @@ static struct variant_data variant_ux500 = {
.clkreg = MCI_CLK_ENABLE,
.clkreg_enable = MCI_ST_UX500_HWFCEN,
.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
+ .clkreg_neg_edge_enable = MCI_ST_UX500_NEG_EDGE,
.datalength_bits = 24,
.sdio = true,
.st_clkdiv = true,
@@ -159,6 +162,7 @@ static struct variant_data variant_ux500v2 = {
.clkreg = MCI_CLK_ENABLE,
.clkreg_enable = MCI_ST_UX500_HWFCEN,
.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
+ .clkreg_neg_edge_enable = MCI_ST_UX500_NEG_EDGE,
.datactrl_mask_ddrmode = MCI_ST_DPSM_DDRMODE,
.datalength_bits = 24,
.sdio = true,
@@ -322,7 +326,7 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
clk |= variant->clkreg_8bit_bus_enable;

if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50)
- clk |= MCI_ST_UX500_NEG_EDGE;
+ clk |= variant->clkreg_neg_edge_enable;

mmci_write_clkreg(host, clk);
}
--
1.9.1


\
 
 \ /
  Last update: 2014-05-28 17:01    [W:0.405 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site