lkml.org 
[lkml]   [2014]   [May]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] usb: pci-quirks: do not access OHCI_FMINTERVAL register on ULI hw
On Wed, 28 May 2014, Nikita Yushchenko wrote:

> 27.05.2014 19:08, Alan Stern пишет:
> > On Tue, 27 May 2014, Nikita Yushchenko wrote:
> >
> >> This access causes hang on Freescale P2020DS board (that has OHCI
> >> provided by ULI 1533 chip).
> >
> > Which access, the read or the write?
>
> things are a bit more complex.
>
> If inserting printk's as below
>
>
> --- a/drivers/usb/host/pci-quirks.c
> +++ b/drivers/usb/host/pci-quirks.c
> @@ -619,16 +619,23 @@ static void quirk_usb_handoff_ohci(struct pci_dev *pdev)
> }
>
> /* software reset of the controller, preserving HcFmInterval */
> + printk("A1\n");
> fminterval = readl(base + OHCI_FMINTERVAL);
> + printk("A2\n");

It would help to print the value of fminterval.

> writel(OHCI_HCR, base + OHCI_CMDSTATUS);
> + printk("A3\n");
>
> /* reset requires max 10 us delay */
> for (cnt = 30; cnt > 0; --cnt) { /* ... allow extra time */
> + printk("A4\n");
> if ((readl(base + OHCI_CMDSTATUS) & OHCI_HCR) == 0)
> break;

And here to print the value obtained by the readl().

> + printk("A5\n");
> udelay(1);
> }
> + printk("A6\n");
> writel(fminterval, base + OHCI_FMINTERVAL);
> + printk("A7\n");
>
> /* Now the controller is safely in SUSPEND and nothing can wake it up */
> iounmap(base);
>
> attempt to boot (using arch/powerpc/configs/mpc85xx_smp_defconfig and deb
> file built by "make p2020ds.dtb" from the same kernel tree) results in
>
> ...
> A1
> random: nonblocking pool is initialized
> irq 26: nobody cared (try booting with the "irqpoll" option)
> CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc6-dirty #5
> Call Trace:
> [effe5ed0] [c000726c] show_stack+0x48/0x15c (unreliable)
> [effe5f10] [c05eece4] dump_stack+0x78/0xa0
> [effe5f20] [c0087acc] __report_bad_irq+0x38/0x100
> [effe5f40] [c0088060] note_interrupt+0x224/0x280
> [effe5f70] [c008563c] handle_irq_event_percpu+0xc8/0x178
> [effe5fa0] [c0085730] handle_irq_event+0x44/0x74
> [effe5fc0] [c0088f88] handle_fasteoi_irq+0xd4/0x1d0
> [effe5fd0] [c0084d20] generic_handle_irq+0x30/0x50
> [effe5fe0] [c00048d0] __do_irq+0x2c/0x70
> [effe5ff0] [c000d9a0] call_do_irq+0x24/0x3c
> [ef047d10] [c00049a0] do_IRQ+0x8c/0xf8
> [ef047d30] [c000f598] ret_from_except+0x0/0x18
> --- Exception: 501 at quirk_usb_early_handoff+0x794/0x85c
> LR = quirk_usb_early_handoff+0x788/0x85c

That exception looks very suspicious. Do you know what it means?

> [ef047e30] [c02bd66c] pci_fixup_device+0xe0/0x19c
> [ef047e60] [c07d4e1c] pci_apply_final_quirks+0x60/0x13c
> [ef047e90] [c0002494] do_one_initcall+0x158/0x19c
> [ef047f00] [c07ba928] kernel_init_freeable+0x130/0x1e4
> [ef047f30] [c0002a78] kernel_init+0x14/0x10c
> [ef047f40] [c000f014] ret_from_kernel_thread+0x5c/0x64
> handlers:
> [<c001cc78>] fsl_pci_pme_handle
> Disabling IRQ #26

It looks like this IRQ 26 stuff has no connection with OHCI, right?

> A2
> A3
> A4
> A5
> A4
> A5
> A4
> A5
> A4
> A5
> A4
>
> and hang.

Meaning that it stops completely, not that it goes into an infinite
loop?

> with my patch applied, board just boots ok and works.
>
>
> > It looks like you haven't read ohci_shutdown() and ohci_run() in
> > drivers/usb/host/ohci-hcd.c. They both access the fminterval register,
> > and this patch doesn't change them.
> >
> > So I don't see why this patch should make any difference to the
> > system's operation.
>
> I think problem is caused by access to OHCI regs from PCI quirks - before
> driver was initialized. ULI1553 southbridge chip could be in strange state
> at this point.

If that is the cause, we ought to be able to see it from the values
printed out by the debugging statements. And if that is so, it's a
serious problem. The southbridge chip really should be working at this
point, because the quirk_usb_handoff_* routines need to be able to
communicate with the host controllers.

Alan Stern

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2014-05-28 17:01    [W:0.096 / U:0.328 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site