lkml.org 
[lkml]   [2014]   [May]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/4] phy: miphy365x: Add Device Tree bindings for the MiPHY365x
Date
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
.../devicetree/bindings/phy/phy-miphy365x.txt | 62 ++++++++++++++++++++++
1 file changed, 62 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-miphy365x.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
new file mode 100644
index 0000000..cb39de1
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
@@ -0,0 +1,62 @@
+STMicroelectronics STi MIPHY365x PHY binding
+============================================
+
+This binding describes a miphy device that is used to control PHY hardware
+for SATA and PCIe.
+
+Required properties:
+- compatible : Should be "st,miphy365x-phy"
+- #phy-cells : Should be 2 (See second example)
+ First cell is the port number from:
+ - MIPHY_PORT_0
+ - MIPHY_PORT_1
+ Second cell is device type from:
+ - MIPHY_TYPE_SATA
+ - MIPHY_TYPE_PCI
+- reg : Address and length of register sets for each device in
+ "reg-names"
+- reg-names : The names of the register addresses corresponding to the
+ registers filled in "reg", from:
+ - sata0: For SATA port 0 registers
+ - sata1: For SATA port 1 registers
+ - pcie0: For PCIE port 0 registers
+ - pcie1: For PCIE port 1 registers
+- st,syscfg : Should be a phandle of the system configuration register group
+ which contain the SATA, PCIe mode setting bits
+
+Optional properties:
+- st,sata-gen : Generation of locally attached SATA IP. Expected values
+ are {1,2,3). If not supplied generation 1 hardware will
+ be expected
+- st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp)
+- st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp)
+
+Example:
+
+ miphy365x_phy: miphy365x@fe382000 {
+ compatible = "st,miphy365x-phy";
+ #phy-cells = <2>;
+ reg = <0xfe382000 0x100>,
+ <0xfe38a000 0x100>,
+ <0xfe394000 0x100>,
+ <0xfe804000 0x100>;
+ reg-names = "sata0", "sata1", "pcie0", "pcie1";
+ st,syscfg = <&syscfg_rear>;
+ };
+
+Specifying phy control of devices
+=================================
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the miphy device node, a port number
+and a device type.
+
+Example:
+
+#include <dt-bindings/phy/phy-miphy365x.h>
+
+ sata0: sata@fe380000 {
+ ...
+ phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>;
+ ...
+ };
--
1.8.3.2


\
 
 \ /
  Last update: 2014-05-23 23:41    [W:3.141 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site