lkml.org 
[lkml]   [2014]   [Apr]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V4 5/5] usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver
Date
Removing this older USB 3.0 DRD controller PHY driver, since
a new driver based on generic phy framework is now available.

Also removing the dt node for older driver from Exynos5250
device tree and updating the dt node for DWC3 controller.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
---

NOTE: This patch should be merged only when the new USB 3.0
DRD phy controller driver is available in the tree from the
patches:
phy: Add new Exynos5 USB 3.0 PHY driver; and
dt: exynos5250: Enable support for generic USB DRD phy

arch/arm/boot/dts/exynos5250.dtsi | 17 +-
drivers/usb/phy/phy-samsung-usb.h | 83 ---------
drivers/usb/phy/phy-samsung-usb3.c | 350 ------------------------------------
3 files changed, 2 insertions(+), 448 deletions(-)
delete mode 100644 drivers/usb/phy/phy-samsung-usb3.c

diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 92c6fcd..1cb1e91 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -512,21 +512,8 @@
compatible = "synopsys,dwc3";
reg = <0x12000000 0x10000>;
interrupts = <0 72 0>;
- usb-phy = <&usb2_phy &usb3_phy>;
- };
- };
-
- usb3_phy: usbphy@12100000 {
- compatible = "samsung,exynos5250-usb3phy";
- reg = <0x12100000 0x100>;
- clocks = <&clock 1>, <&clock 286>;
- clock-names = "ext_xtal", "usbdrd30";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- usbphy-sys {
- reg = <0x10040704 0x8>;
+ phys = <&usbdrd_phy 0>, <&usbdrd_phy 1>;
+ phy-names = "usb2-phy", "usb3-phy";
};
};

diff --git a/drivers/usb/phy/phy-samsung-usb.h b/drivers/usb/phy/phy-samsung-usb.h
index 68771bf..ced8b65 100644
--- a/drivers/usb/phy/phy-samsung-usb.h
+++ b/drivers/usb/phy/phy-samsung-usb.h
@@ -155,86 +155,6 @@

#define EXYNOS5_PHY_OTG_TUNE (0x40)

-/* EXYNOS5: USB 3.0 DRD */
-#define EXYNOS5_DRD_LINKSYSTEM (0x04)
-
-#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
-#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
-#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
-
-#define EXYNOS5_DRD_PHYUTMI (0x08)
-
-#define PHYUTMI_OTGDISABLE (0x1 << 6)
-#define PHYUTMI_FORCESUSPEND (0x1 << 1)
-#define PHYUTMI_FORCESLEEP (0x1 << 0)
-
-#define EXYNOS5_DRD_PHYPIPE (0x0c)
-
-#define EXYNOS5_DRD_PHYCLKRST (0x10)
-
-#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
-#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
-
-#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
-#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
-
-#define PHYCLKRST_SSC_EN (0x1 << 20)
-#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
-#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
-
-#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x02 << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
-#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
-
-#define PHYCLKRST_FSEL_MASK (0x3f << 5)
-#define PHYCLKRST_FSEL(_x) ((_x) << 5)
-#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
-#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
-#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
-#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
-
-#define PHYCLKRST_RETENABLEN (0x1 << 4)
-
-#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
-#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
-#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
-
-#define PHYCLKRST_PORTRESET (0x1 << 1)
-#define PHYCLKRST_COMMONONN (0x1 << 0)
-
-#define EXYNOS5_DRD_PHYREG0 (0x14)
-#define EXYNOS5_DRD_PHYREG1 (0x18)
-
-#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
-
-#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
-#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
-#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
-
-#define EXYNOS5_DRD_PHYPARAM1 (0x20)
-
-#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
-#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
-
-#define EXYNOS5_DRD_PHYTERM (0x24)
-
-#define EXYNOS5_DRD_PHYTEST (0x28)
-
-#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
-#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
-
-#define EXYNOS5_DRD_PHYADP (0x2c)
-
-#define EXYNOS5_DRD_PHYBATCHG (0x30)
-
-#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
-
-#define EXYNOS5_DRD_PHYRESUME (0x34)
-#define EXYNOS5_DRD_LINKPORT (0x44)
-
#ifndef MHZ
#define MHZ (1000*1000)
#endif
@@ -262,8 +182,6 @@ struct samsung_usbphy;
* @cpu_type: machine identifier
* @devphy_en_mask: device phy enable mask for PHY CONTROL register
* @hostphy_en_mask: host phy enable mask for PHY CONTROL register
- * @devphy_reg_offset: offset to DEVICE PHY CONTROL register from
- * mapped address of system controller.
* @hostphy_reg_offset: offset to HOST PHY CONTROL register from
* mapped address of system controller.
*
@@ -279,7 +197,6 @@ struct samsung_usbphy_drvdata {
int cpu_type;
int devphy_en_mask;
int hostphy_en_mask;
- u32 devphy_reg_offset;
u32 hostphy_reg_offset;
int (*rate_to_clksel)(struct samsung_usbphy *, unsigned long);
void (*set_isolation)(struct samsung_usbphy *, bool);
diff --git a/drivers/usb/phy/phy-samsung-usb3.c b/drivers/usb/phy/phy-samsung-usb3.c
deleted file mode 100644
index cc08192..0000000
--- a/drivers/usb/phy/phy-samsung-usb3.c
+++ /dev/null
@@ -1,350 +0,0 @@
-/* linux/drivers/usb/phy/phy-samsung-usb3.c
- *
- * Copyright (c) 2013 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * Author: Vivek Gautam <gautam.vivek@samsung.com>
- *
- * Samsung USB 3.0 PHY transceiver; talks to DWC3 controller.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/usb/samsung_usb_phy.h>
-#include <linux/platform_data/samsung-usbphy.h>
-
-#include "phy-samsung-usb.h"
-
-/*
- * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
- */
-static u32 samsung_usb3phy_set_refclk(struct samsung_usbphy *sphy)
-{
- u32 reg;
- u32 refclk;
-
- refclk = sphy->ref_clk_freq;
-
- reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
- PHYCLKRST_FSEL(refclk);
-
- switch (refclk) {
- case FSEL_CLKSEL_50M:
- reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
- PHYCLKRST_SSC_REFCLKSEL(0x00));
- break;
- case FSEL_CLKSEL_20M:
- reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
- PHYCLKRST_SSC_REFCLKSEL(0x00));
- break;
- case FSEL_CLKSEL_19200K:
- reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
- PHYCLKRST_SSC_REFCLKSEL(0x88));
- break;
- case FSEL_CLKSEL_24M:
- default:
- reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
- PHYCLKRST_SSC_REFCLKSEL(0x88));
- break;
- }
-
- return reg;
-}
-
-static void samsung_exynos5_usb3phy_enable(struct samsung_usbphy *sphy)
-{
- void __iomem *regs = sphy->regs;
- u32 phyparam0;
- u32 phyparam1;
- u32 linksystem;
- u32 phybatchg;
- u32 phytest;
- u32 phyclkrst;
-
- /* Reset USB 3.0 PHY */
- writel(0x0, regs + EXYNOS5_DRD_PHYREG0);
-
- phyparam0 = readl(regs + EXYNOS5_DRD_PHYPARAM0);
- /* Select PHY CLK source */
- phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
- /* Set Loss-of-Signal Detector sensitivity */
- phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
- phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
- writel(phyparam0, regs + EXYNOS5_DRD_PHYPARAM0);
-
- writel(0x0, regs + EXYNOS5_DRD_PHYRESUME);
-
- /*
- * Setting the Frame length Adj value[6:1] to default 0x20
- * See xHCI 1.0 spec, 5.2.4
- */
- linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
- LINKSYSTEM_FLADJ(0x20);
- writel(linksystem, regs + EXYNOS5_DRD_LINKSYSTEM);
-
- phyparam1 = readl(regs + EXYNOS5_DRD_PHYPARAM1);
- /* Set Tx De-Emphasis level */
- phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
- phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
- writel(phyparam1, regs + EXYNOS5_DRD_PHYPARAM1);
-
- phybatchg = readl(regs + EXYNOS5_DRD_PHYBATCHG);
- phybatchg |= PHYBATCHG_UTMI_CLKSEL;
- writel(phybatchg, regs + EXYNOS5_DRD_PHYBATCHG);
-
- /* PHYTEST POWERDOWN Control */
- phytest = readl(regs + EXYNOS5_DRD_PHYTEST);
- phytest &= ~(PHYTEST_POWERDOWN_SSP |
- PHYTEST_POWERDOWN_HSP);
- writel(phytest, regs + EXYNOS5_DRD_PHYTEST);
-
- /* UTMI Power Control */
- writel(PHYUTMI_OTGDISABLE, regs + EXYNOS5_DRD_PHYUTMI);
-
- phyclkrst = samsung_usb3phy_set_refclk(sphy);
-
- phyclkrst |= PHYCLKRST_PORTRESET |
- /* Digital power supply in normal operating mode */
- PHYCLKRST_RETENABLEN |
- /* Enable ref clock for SS function */
- PHYCLKRST_REF_SSP_EN |
- /* Enable spread spectrum */
- PHYCLKRST_SSC_EN |
- /* Power down HS Bias and PLL blocks in suspend mode */
- PHYCLKRST_COMMONONN;
-
- writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
-
- udelay(10);
-
- phyclkrst &= ~(PHYCLKRST_PORTRESET);
- writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
-}
-
-static void samsung_exynos5_usb3phy_disable(struct samsung_usbphy *sphy)
-{
- u32 phyutmi;
- u32 phyclkrst;
- u32 phytest;
- void __iomem *regs = sphy->regs;
-
- phyutmi = PHYUTMI_OTGDISABLE |
- PHYUTMI_FORCESUSPEND |
- PHYUTMI_FORCESLEEP;
- writel(phyutmi, regs + EXYNOS5_DRD_PHYUTMI);
-
- /* Resetting the PHYCLKRST enable bits to reduce leakage current */
- phyclkrst = readl(regs + EXYNOS5_DRD_PHYCLKRST);
- phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
- PHYCLKRST_SSC_EN |
- PHYCLKRST_COMMONONN);
- writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
-
- /* Control PHYTEST to remove leakage current */
- phytest = readl(regs + EXYNOS5_DRD_PHYTEST);
- phytest |= (PHYTEST_POWERDOWN_SSP |
- PHYTEST_POWERDOWN_HSP);
- writel(phytest, regs + EXYNOS5_DRD_PHYTEST);
-}
-
-static int samsung_usb3phy_init(struct usb_phy *phy)
-{
- struct samsung_usbphy *sphy;
- unsigned long flags;
- int ret = 0;
-
- sphy = phy_to_sphy(phy);
-
- /* Enable the phy clock */
- ret = clk_prepare_enable(sphy->clk);
- if (ret) {
- dev_err(sphy->dev, "%s: clk_prepare_enable failed\n", __func__);
- return ret;
- }
-
- spin_lock_irqsave(&sphy->lock, flags);
-
- /* setting default phy-type for USB 3.0 */
- samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_DEVICE);
-
- /* Disable phy isolation */
- if (sphy->drv_data->set_isolation)
- sphy->drv_data->set_isolation(sphy, false);
-
- /* Initialize usb phy registers */
- sphy->drv_data->phy_enable(sphy);
-
- spin_unlock_irqrestore(&sphy->lock, flags);
-
- /* Disable the phy clock */
- clk_disable_unprepare(sphy->clk);
-
- return ret;
-}
-
-/*
- * The function passed to the usb driver for phy shutdown
- */
-static void samsung_usb3phy_shutdown(struct usb_phy *phy)
-{
- struct samsung_usbphy *sphy;
- unsigned long flags;
-
- sphy = phy_to_sphy(phy);
-
- if (clk_prepare_enable(sphy->clk)) {
- dev_err(sphy->dev, "%s: clk_prepare_enable failed\n", __func__);
- return;
- }
-
- spin_lock_irqsave(&sphy->lock, flags);
-
- /* setting default phy-type for USB 3.0 */
- samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_DEVICE);
-
- /* De-initialize usb phy registers */
- sphy->drv_data->phy_disable(sphy);
-
- /* Enable phy isolation */
- if (sphy->drv_data->set_isolation)
- sphy->drv_data->set_isolation(sphy, true);
-
- spin_unlock_irqrestore(&sphy->lock, flags);
-
- clk_disable_unprepare(sphy->clk);
-}
-
-static int samsung_usb3phy_probe(struct platform_device *pdev)
-{
- struct samsung_usbphy *sphy;
- struct samsung_usbphy_data *pdata = dev_get_platdata(&pdev->dev);
- struct device *dev = &pdev->dev;
- struct resource *phy_mem;
- void __iomem *phy_base;
- struct clk *clk;
- int ret;
-
- phy_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- phy_base = devm_ioremap_resource(dev, phy_mem);
- if (IS_ERR(phy_base))
- return PTR_ERR(phy_base);
-
- sphy = devm_kzalloc(dev, sizeof(*sphy), GFP_KERNEL);
- if (!sphy)
- return -ENOMEM;
-
- clk = devm_clk_get(dev, "usbdrd30");
- if (IS_ERR(clk)) {
- dev_err(dev, "Failed to get device clock\n");
- return PTR_ERR(clk);
- }
-
- sphy->dev = dev;
-
- if (dev->of_node) {
- ret = samsung_usbphy_parse_dt(sphy);
- if (ret < 0)
- return ret;
- } else {
- if (!pdata) {
- dev_err(dev, "no platform data specified\n");
- return -EINVAL;
- }
- }
-
- sphy->plat = pdata;
- sphy->regs = phy_base;
- sphy->clk = clk;
- sphy->phy.dev = sphy->dev;
- sphy->phy.label = "samsung-usb3phy";
- sphy->phy.type = USB_PHY_TYPE_USB3;
- sphy->phy.init = samsung_usb3phy_init;
- sphy->phy.shutdown = samsung_usb3phy_shutdown;
- sphy->drv_data = samsung_usbphy_get_driver_data(pdev);
-
- sphy->ref_clk_freq = samsung_usbphy_get_refclk_freq(sphy);
- if (sphy->ref_clk_freq < 0)
- return -EINVAL;
-
- spin_lock_init(&sphy->lock);
-
- platform_set_drvdata(pdev, sphy);
-
- return usb_add_phy_dev(&sphy->phy);
-}
-
-static int samsung_usb3phy_remove(struct platform_device *pdev)
-{
- struct samsung_usbphy *sphy = platform_get_drvdata(pdev);
-
- usb_remove_phy(&sphy->phy);
-
- if (sphy->pmuregs)
- iounmap(sphy->pmuregs);
- if (sphy->sysreg)
- iounmap(sphy->sysreg);
-
- return 0;
-}
-
-static struct samsung_usbphy_drvdata usb3phy_exynos5 = {
- .cpu_type = TYPE_EXYNOS5250,
- .devphy_en_mask = EXYNOS_USBPHY_ENABLE,
- .rate_to_clksel = samsung_usbphy_rate_to_clksel_4x12,
- .set_isolation = samsung_usbphy_set_isolation_4210,
- .phy_enable = samsung_exynos5_usb3phy_enable,
- .phy_disable = samsung_exynos5_usb3phy_disable,
-};
-
-#ifdef CONFIG_OF
-static const struct of_device_id samsung_usbphy_dt_match[] = {
- {
- .compatible = "samsung,exynos5250-usb3phy",
- .data = &usb3phy_exynos5
- },
- {},
-};
-MODULE_DEVICE_TABLE(of, samsung_usbphy_dt_match);
-#endif
-
-static struct platform_device_id samsung_usbphy_driver_ids[] = {
- {
- .name = "exynos5250-usb3phy",
- .driver_data = (unsigned long)&usb3phy_exynos5,
- },
- {},
-};
-
-MODULE_DEVICE_TABLE(platform, samsung_usbphy_driver_ids);
-
-static struct platform_driver samsung_usb3phy_driver = {
- .probe = samsung_usb3phy_probe,
- .remove = samsung_usb3phy_remove,
- .id_table = samsung_usbphy_driver_ids,
- .driver = {
- .name = "samsung-usb3phy",
- .owner = THIS_MODULE,
- .of_match_table = of_match_ptr(samsung_usbphy_dt_match),
- },
-};
-
-module_platform_driver(samsung_usb3phy_driver);
-
-MODULE_DESCRIPTION("Samsung USB 3.0 phy controller");
-MODULE_AUTHOR("Vivek Gautam <gautam.vivek@samsung.com>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:samsung-usb3phy");
--
1.7.10.4


\
 
 \ /
  Last update: 2014-04-08 17:01    [W:0.335 / U:6.664 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site