lkml.org 
[lkml]   [2014]   [Apr]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v1 00/11] Add Qualcomm SD Card Controller support.
Date
From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

Hi Russell,

This patch series adds Qualcomm SD Card Controller support in pl180 mmci
driver. QCom SDCC is basically a pl180, but bit more customized, some of the
register layouts and offsets are different to the ones mentioned in pl180
datasheet. The plan is to totally remove the standalone SDCC driver
drivers/mmc/host/msm_sdcc.* and start using generic mmci driver for all
Qualcomm parts, as we get chance to test on other Qcom boards.

To start using the existing mmci driver, a fake amba id for Qualcomm is added
in patches:
ARM: amba: Add Qualcomm vendor ID.
mmc: mmci: Add Qualcomm Id to amba id table.

Second change is, adding a 3 clock cycle delay for register writes on QCOM
SDCC
registers, which is done in patches:
mmc: mmci: Add register read/write wrappers.
mmc: mmci: Qcomm: Add 3 clock cycle delay after each register write

Third change was to accommodate DATCTRL and MMCICLK register layout changes in
Qcom SDCC. Which is done in patches:
mmc: mmci: Add Qcom datactrl register variant
mmc: mmci: Add Qcom variations to MCICommand register.
mmc: mmci: Qcom fix MCICLK register settings.
mmc: mmci: Add clock support for Qualcomm.

Fourth major change was to add qcom specfic pio read function, the need for
this is because the way MCIFIFOCNT register behaved in QCOM SDCC is very
different to the one in pl180. This change is done in patch:
mmc: mmci: Add Qcom specific pio_read function.

Last some Qcom unrelated changes to support Qcom are done in patches:
mmc: mmci: use NSEC_PER_SEC macro
mmc: mmci: move ST specific register extensions access under condition.

This patches are tested v3.15-rc3 in PIO mode on IFC6410 board with both eMMC
and external SD card. I would appreciate any feedback on the patches.
I would like to get this for v3.16.

Thanks,
srini

Srinivas Kandagatla (11):
ARM: amba: Add Qualcomm vendor ID.
mmc: mmci: Add Qualcomm Id to amba id table
mmc: mmci: Add Qcom datactrl register variant
mmc: mmci: Add register read/write wrappers.
mmc: mmci: use NSEC_PER_SEC macro
mmc: mmci: Qcomm: Add 3 clock cycle delay after register write
mmc: mmci: move ST specific register extensions access under
condition.
mmc: mmci: Qcom fix MCICLK register settings.
mmc: mmci: Add clock support for Qualcomm.
mmc: mmci: Add Qcom variations to MCICommand register.
mmc: mmci: Add Qcom specific pio_read function.

drivers/mmc/host/mmci.c | 243 +++++++++++++++++++++++++++++++++-------------
drivers/mmc/host/mmci.h | 28 ++++++
include/linux/amba/bus.h | 1 +
3 files changed, 206 insertions(+), 66 deletions(-)

--
1.7.9.5



\
 
 \ /
  Last update: 2014-04-29 10:41    [W:1.541 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site