lkml.org 
[lkml]   [2014]   [Apr]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/3] sched, balancing: Update rq->max_idle_balance_cost whenever newidle balance is attempted
Hi Jason,

On 04/25/2014 03:48 AM, Jason Low wrote:
> On Thu, 2014-04-24 at 19:14 +0200, Peter Zijlstra wrote:
>> On Thu, Apr 24, 2014 at 09:53:37AM -0700, Jason Low wrote:
>>>
>>> So I thought that the original rationale (commit 1bd77f2d) behind
>>> updating rq->next_balance in idle_balance() is that, if we are going
>>> idle (!pulled_task), we want to ensure that the next_balance gets
>>> calculated without the busy_factor.
>>>
>>> If the rq is busy, then rq->next_balance gets updated based on
>>> sd->interval * busy_factor. However, when the rq goes from "busy"
>>> to idle, rq->next_balance might still have been calculated under
>>> the assumption that the rq is busy. Thus, if we are going idle, we
>>> would then properly update next_balance without the busy factor
>>> if we update when !pulled_task.
>>>
>>
>> Its late here and I'm confused!
>>
>> So the for_each_domain() loop calculates a new next_balance based on
>> ->balance_interval (which has that busy_factor on, right).
>>
>> But if it fails to pull anything, we'll (potentially) iterate the entire
>> tree up to the largest domain; and supposedly set next_balanced to the
>> largest possible interval.
>>
>> So when we go from busy to idle (!pulled_task), we actually set
>> ->next_balance to the longest interval. Whereas the commit you
>> referenced says it sets it to a shorter while.
>>
>> Not seeing it.
>
> So this is the way I understand that code:
>
> In rebalance_domain, next_balance is suppose to be set to the
> minimum of all sd->last_balance + interval so that we properly call
> into rebalance_domains() if one of the domains is due for a balance.
>
> In the domain traversals:
>
> if (time_after(next_balance, sd->last_balance + interval))
> next_balance = sd->last_balance + interval;
>
> we update next_balance to a new value if the current next_balance
> is after, and we only update next_balance to a smaller value.
>
> In rebalance_domains, we have code:
>
> interval = sd->balance_interval;
> if (idle != CPU_IDLE)
> interval *= sd->busy_factor;
>
> ...
>
> if (time_after(next_balance, sd->last_balance + interval)) {
> next_balance = sd->last_balance + interval;
>
> ...
>
> rq->next_balance = next_balance;
>
> In the CPU_IDLE case, interval would not include the busy factor,
> whereas in the !CPU_IDLE case, we multiply the interval by the
> sd->busy_factor.
>
> So as an example, if a CPU is not idle and we run this:
>
> rebalance_domain()
> interval = 1 ms;
> if (idle != CPU_IDLE)
> interval *= 64;
>
> next_balance = sd->last_balance + 64 ms
>
> rq->next_balance = next_balance
>
> The rq->next_balance is set to a large value since the CPU is not idle.
>
> Then, let's say the CPU then goes idle 1 ms later. The
> rq->next_balance can be up to 63 ms later, because we computed
> it when the CPU is not idle. Now that we are going idle,
> we would have to wait a long time for the next balance.
>
> So I believe that the initial reason why rq->next_balance was
> updated in idle_balance is that if the CPU is in the process
> of going idle (!pulled_task in idle_balance()), we can reset the
> rq->next_balance based on the interval = 1 ms, as oppose to
> having it remain up to 64 ms later (in idle_balance(), interval
> doesn't get multiplied by sd->busy_factor).

I agree with this. However I am concerned with an additional point that
I have mentioned in my reply to Peter's mail on this thread.

Should we verify if rq->next_balance update is independent of
pulled_tasks? sd->balance_interval is changed during load_balance() and
rq->next_balance should perhaps consider that?

Regards
Preeti U Murthy
>
>
>



\
 
 \ /
  Last update: 2014-04-25 07:41    [W:0.247 / U:0.124 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site