lkml.org 
[lkml]   [2014]   [Apr]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/4] ARM: at91/dt: define sam9n12 clocks
Hi Alexandre,

On 14/04/2014 10:56, Alexandre Belloni wrote:
> On 14/04/2014 at 10:16:37 +0200, Boris Brezillon wrote :
>> Define sam9n12 clocks and make use of them in peripheral definitions.
>>
>> Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
>> ---
>> arch/arm/boot/dts/at91sam9n12.dtsi | 350 ++++++++++++++++++++++++++++++++++++-
>> 1 file changed, 348 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
>> index 9f04808..4d036a3 100644
>> --- a/arch/arm/boot/dts/at91sam9n12.dtsi
>> +++ b/arch/arm/boot/dts/at91sam9n12.dtsi
>> @@ -12,6 +12,7 @@
>> #include <dt-bindings/pinctrl/at91.h>
>> #include <dt-bindings/interrupt-controller/irq.h>
>> #include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/clk/at91.h>
>>
>> / {
>> model = "Atmel AT91SAM9N12 SoC";
>> @@ -49,6 +50,20 @@
>> reg = <0x20000000 0x10000000>;
>> };
>>
>> + clocks {
>> + slow_xtal: slow_xtal {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <0>;
>> + };
>> +
>> + main_xtal: main_xtal {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <0>;
>> + };
> You can put those two xtal nodes directly under root, as mentioned by
> Mark Rutland:
>
> "A "clocks" container is non-standard, and not guarantee to probe. The
> fact these clocks probe currently is an artifact of the current
> organisation of Linux rather than any conscious decision."

Okay, I will fix it for the next version.

Thanks.

Boris

>> + };
>> +
>> ahb {
>> compatible = "simple-bus";
>> #address-cells = <1>;
>> @@ -75,8 +90,280 @@
>> };
>>
>> pmc: pmc@fffffc00 {
>> - compatible = "atmel,at91rm9200-pmc";
>> - reg = <0xfffffc00 0x100>;
>> + compatible = "atmel,at91sam9n12-pmc";
>> + reg = <0xfffffc00 0x200>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + interrupt-controller;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #interrupt-cells = <1>;
>> +
>> + main_rc_osc: main_rc_osc {
>> + compatible = "atmel,at91sam9x5-clk-main-rc-osc";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_MOSCRCS>;
>> + clock-frequency = <12000000>;
>> + clock-accuracy = <50000000>;
>> + };
>> +
>> + main_osc: main_osc {
>> + compatible = "atmel,at91sam9x5-clk-main-osc";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_MOSCS>;
>> + clocks = <&main_xtal>;
>> + };
>> +
>> + main: mainck {
>> + compatible = "atmel,at91sam9x5-clk-main";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_MOSCSELS>;
>> + clocks = <&main_rc_osc>, <&main_osc>;
>> + };
>> +
>> + plla: pllack {
>> + compatible = "atmel,at91rm9200-clk-pll";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_LOCKA>;
>> + clocks = <&main>;
>> + reg = <0>;
>> + atmel,clk-input-range = <2000000 32000000>;
>> + #atmel,pll-clk-output-range-cells = <4>;
>> + atmel,pll-clk-output-ranges = <745000000 800000000 0 0>,
>> + <695000000 750000000 1 0>,
>> + <645000000 700000000 2 0>,
>> + <595000000 650000000 3 0>,
>> + <545000000 600000000 0 1>,
>> + <495000000 555000000 1 1>,
>> + <445000000 500000000 1 2>,
>> + <400000000 450000000 1 3>;
>> + };
>> +
>> + plladiv: plladivck {
>> + compatible = "atmel,at91sam9x5-clk-plldiv";
>> + #clock-cells = <0>;
>> + clocks = <&plla>;
>> + };
>> +
>> + pllb: pllbck {
>> + compatible = "atmel,at91rm9200-clk-pll";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_LOCKB>;
>> + clocks = <&main>;
>> + reg = <1>;
>> + atmel,clk-input-range = <2000000 32000000>;
>> + #atmel,pll-clk-output-range-cells = <3>;
>> + atmel,pll-clk-output-ranges = <30000000 100000000 0>;
>> + };
>> +
>> + mck: masterck {
>> + compatible = "atmel,at91sam9x5-clk-master";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
>> + clocks = <&clk32k>, <&main>, <&plladiv>, <&pllb>;
>> + atmel,clk-output-range = <0 133333333>;
>> + atmel,clk-divisors = <1 2 4 3>;
>> + atmel,master-clk-have-div3-pres;
>> + };
>> +
>> + usb: usbck {
>> + compatible = "atmel,at91sam9n12-clk-usb";
>> + #clock-cells = <0>;
>> + clocks = <&pllb>;
>> + };
>> +
>> + prog: progck {
>> + compatible = "atmel,at91sam9x5-clk-programmable";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupt-parent = <&pmc>;
>> + clocks = <&clk32k>, <&main>, <&plladiv>, <&pllb>, <&mck>;
>> +
>> + prog0: prog0 {
>> + #clock-cells = <0>;
>> + reg = <0>;
>> + interrupts = <AT91_PMC_PCKRDY(0)>;
>> + };
>> +
>> + prog1: prog1 {
>> + #clock-cells = <0>;
>> + reg = <1>;
>> + interrupts = <AT91_PMC_PCKRDY(1)>;
>> + };
>> + };
>> +
>> + systemck {
>> + compatible = "atmel,at91rm9200-clk-system";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ddrck: ddrck {
>> + #clock-cells = <0>;
>> + reg = <2>;
>> + clocks = <&mck>;
>> + };
>> +
>> + lcdck: lcdck {
>> + #clock-cells = <0>;
>> + reg = <3>;
>> + clocks = <&mck>;
>> + };
>> +
>> + uhpck: uhpck {
>> + #clock-cells = <0>;
>> + reg = <6>;
>> + clocks = <&usb>;
>> + };
>> +
>> + udpck: udpck {
>> + #clock-cells = <0>;
>> + reg = <7>;
>> + clocks = <&usb>;
>> + };
>> +
>> + pck0: pck0 {
>> + #clock-cells = <0>;
>> + reg = <8>;
>> + clocks = <&prog0>;
>> + };
>> +
>> + pck1: pck1 {
>> + #clock-cells = <0>;
>> + reg = <9>;
>> + clocks = <&prog1>;
>> + };
>> + };
>> +
>> + periphck {
>> + compatible = "atmel,at91sam9x5-clk-peripheral";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&mck>;
>> +
>> + pioAB_clk: pioAB_clk {
>> + #clock-cells = <0>;
>> + reg = <2>;
>> + };
>> +
>> + pioCD_clk: pioCD_clk {
>> + #clock-cells = <0>;
>> + reg = <3>;
>> + };
>> +
>> + fuse_clk: fuse_clk {
>> + #clock-cells = <0>;
>> + reg = <4>;
>> + };
>> +
>> + usart0_clk: usart0_clk {
>> + #clock-cells = <0>;
>> + reg = <5>;
>> + };
>> +
>> + usart1_clk: usart1_clk {
>> + #clock-cells = <0>;
>> + reg = <6>;
>> + };
>> +
>> + usart2_clk: usart2_clk {
>> + #clock-cells = <0>;
>> + reg = <7>;
>> + };
>> +
>> + usart3_clk: usart3_clk {
>> + #clock-cells = <0>;
>> + reg = <8>;
>> + };
>> +
>> + twi0_clk: twi0_clk {
>> + reg = <9>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + twi1_clk: twi1_clk {
>> + #clock-cells = <0>;
>> + reg = <10>;
>> + };
>> +
>> + mci0_clk: mci0_clk {
>> + #clock-cells = <0>;
>> + reg = <12>;
>> + };
>> +
>> + spi0_clk: spi0_clk {
>> + #clock-cells = <0>;
>> + reg = <13>;
>> + };
>> +
>> + spi1_clk: spi1_clk {
>> + #clock-cells = <0>;
>> + reg = <14>;
>> + };
>> +
>> + uart0_clk: uart0_clk {
>> + #clock-cells = <0>;
>> + reg = <15>;
>> + };
>> +
>> + uart1_clk: uart1_clk {
>> + #clock-cells = <0>;
>> + reg = <16>;
>> + };
>> +
>> + tcb_clk: tcb_clk {
>> + #clock-cells = <0>;
>> + reg = <17>;
>> + };
>> +
>> + pwm_clk: pwm_clk {
>> + #clock-cells = <0>;
>> + reg = <18>;
>> + };
>> +
>> + adc_clk: adc_clk {
>> + #clock-cells = <0>;
>> + reg = <19>;
>> + };
>> +
>> + dma0_clk: dma0_clk {
>> + #clock-cells = <0>;
>> + reg = <20>;
>> + };
>> +
>> + uhphs_clk: uhphs_clk {
>> + #clock-cells = <0>;
>> + reg = <22>;
>> + };
>> +
>> + udphs_clk: udphs_clk {
>> + #clock-cells = <0>;
>> + reg = <23>;
>> + };
>> +
>> + lcdc_clk: lcdc_clk {
>> + #clock-cells = <0>;
>> + reg = <25>;
>> + };
>> +
>> + sha_clk: sha_clk {
>> + #clock-cells = <0>;
>> + reg = <27>;
>> + };
>> +
>> + ssc0_clk: ssc0_clk {
>> + #clock-cells = <0>;
>> + reg = <28>;
>> + };
>> +
>> + aes_clk: aes_clk {
>> + #clock-cells = <0>;
>> + reg = <29>;
>> + };
>> +
>> + trng_clk: trng_clk {
>> + #clock-cells = <0>;
>> + reg = <30>;
>> + };
>> + };
>> };
>>
>> rstc@fffffe00 {
>> @@ -88,6 +375,7 @@
>> compatible = "atmel,at91sam9260-pit";
>> reg = <0xfffffe30 0xf>;
>> interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&mck>;
>> };
>>
>> shdwc@fffffe10 {
>> @@ -95,12 +383,38 @@
>> reg = <0xfffffe10 0x10>;
>> };
>>
>> + sckc@fffffe50 {
>> + compatible = "atmel,at91sam9x5-sckc";
>> + reg = <0xfffffe50 0x4>;
>> +
>> + slow_osc: slow_osc {
>> + compatible = "atmel,at91sam9x5-clk-slow-osc";
>> + #clock-cells = <0>;
>> + clocks = <&slow_xtal>;
>> + };
>> +
>> + slow_rc_osc: slow_rc_osc {
>> + compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
>> + #clock-cells = <0>;
>> + clock-frequency = <32768>;
>> + clock-accuracy = <50000000>;
>> + };
>> +
>> + clk32k: slck {
>> + compatible = "atmel,at91sam9x5-clk-slow";
>> + #clock-cells = <0>;
>> + clocks = <&slow_rc_osc>, <&slow_osc>;
>> + };
>> + };
>> +
>> mmc0: mmc@f0008000 {
>> compatible = "atmel,hsmci";
>> reg = <0xf0008000 0x600>;
>> interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
>> dmas = <&dma 1 AT91_DMA_CFG_PER_ID(0)>;
>> dma-names = "rxtx";
>> + clocks = <&mci0_clk>;
>> + clock-names = "mci_clk";
>> #address-cells = <1>;
>> #size-cells = <0>;
>> status = "disabled";
>> @@ -110,12 +424,16 @@
>> compatible = "atmel,at91sam9x5-tcb";
>> reg = <0xf8008000 0x100>;
>> interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
>> + clocks = <&tcb_clk>;
>> + clock-names = "t0_clk";
>> };
>>
>> tcb1: timer@f800c000 {
>> compatible = "atmel,at91sam9x5-tcb";
>> reg = <0xf800c000 0x100>;
>> interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
>> + clocks = <&tcb_clk>;
>> + clock-names = "t0_clk";
>> };
>>
>> dma: dma-controller@ffffec00 {
>> @@ -123,6 +441,8 @@
>> reg = <0xffffec00 0x200>;
>> interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
>> #dma-cells = <2>;
>> + clocks = <&dma0_clk>;
>> + clock-names = "dma_clk";
>> };
>>
>> pinctrl@fffff400 {
>> @@ -392,6 +712,7 @@
>> gpio-controller;
>> interrupt-controller;
>> #interrupt-cells = <2>;
>> + clocks = <&pioAB_clk>;
>> };
>>
>> pioB: gpio@fffff600 {
>> @@ -402,6 +723,7 @@
>> gpio-controller;
>> interrupt-controller;
>> #interrupt-cells = <2>;
>> + clocks = <&pioAB_clk>;
>> };
>>
>> pioC: gpio@fffff800 {
>> @@ -412,6 +734,7 @@
>> gpio-controller;
>> interrupt-controller;
>> #interrupt-cells = <2>;
>> + clocks = <&pioCD_clk>;
>> };
>>
>> pioD: gpio@fffffa00 {
>> @@ -422,6 +745,7 @@
>> gpio-controller;
>> interrupt-controller;
>> #interrupt-cells = <2>;
>> + clocks = <&pioCD_clk>;
>> };
>> };
>>
>> @@ -431,6 +755,8 @@
>> interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_dbgu>;
>> + clocks = <&mck>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -443,6 +769,8 @@
>> dma-names = "tx", "rx";
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
>> + clocks = <&ssc0_clk>;
>> + clock-names = "pclk";
>> status = "disabled";
>> };
>>
>> @@ -452,6 +780,8 @@
>> interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_usart0>;
>> + clocks = <&usart0_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -461,6 +791,8 @@
>> interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_usart1>;
>> + clocks = <&usart1_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -470,6 +802,8 @@
>> interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_usart2>;
>> + clocks = <&usart2_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -479,6 +813,8 @@
>> interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_usart3>;
>> + clocks = <&usart3_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -493,6 +829,7 @@
>> #size-cells = <0>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_i2c0>;
>> + clocks = <&twi0_clk>;
>> status = "disabled";
>> };
>>
>> @@ -507,6 +844,7 @@
>> #size-cells = <0>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_i2c1>;
>> + clocks = <&twi1_clk>;
>> status = "disabled";
>> };
>>
>> @@ -521,6 +859,8 @@
>> dma-names = "tx", "rx";
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_spi0>;
>> + clocks = <&spi0_clk>;
>> + clock-names = "spi_clk";
>> status = "disabled";
>> };
>>
>> @@ -535,6 +875,8 @@
>> dma-names = "tx", "rx";
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_spi1>;
>> + clocks = <&spi1_clk>;
>> + clock-names = "spi_clk";
>> status = "disabled";
>> };
>>
>> @@ -554,6 +896,7 @@
>> reg = <0xf8034000 0x300>;
>> interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
>> #pwm-cells = <3>;
>> + clocks = <&pwm_clk>;
>> status = "disabled";
>> };
>> };
>> @@ -584,6 +927,9 @@
>> compatible = "atmel,at91rm9200-ohci", "usb-ohci";
>> reg = <0x00500000 0x00100000>;
>> interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
>> + clocks = <&usb>, <&uhphs_clk>, <&udphs_clk>,
>> + <&uhpck>;
>> + clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
>> status = "disabled";
>> };
>> };
>> --
>> 1.8.3.2
>>

--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com



\
 
 \ /
  Last update: 2014-04-14 15:01    [W:0.090 / U:24.572 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site