lkml.org 
[lkml]   [2014]   [Feb]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v6 5/6] spmi: document the PMIC arbiter SPMI bindings
Date
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
---
.../bindings/spmi/qcom,spmi-pmic-arb.txt | 61 ++++++++++++++++++++++
1 file changed, 61 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt

diff --git a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
new file mode 100644
index 0000000..715d099
--- /dev/null
+++ b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
@@ -0,0 +1,61 @@
+Qualcomm SPMI Controller (PMIC Arbiter)
+
+The SPMI PMIC Arbiter is found on the Snapdragon 800 Series. It is an SPMI
+controller with wrapping arbitration logic to allow for multiple on-chip
+devices to control a single SPMI master.
+
+The PMIC Arbiter can also act as an interrupt controller, providing interrupts
+to slave devices.
+
+See spmi.txt for the generic SPMI controller binding requirements for child
+nodes.
+
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
+generic interrupt controller binding documentation.
+
+Required properties:
+- compatible : should be "qcom,spmi-pmic-arb".
+- reg-names : must contain:
+ "core" - core registers
+ "intr" - interrupt controller registers
+ "cnfg" - configuration registers
+- reg : address + size pairs describing the PMIC arb register sets; order must
+ correspond with the order of entries in reg-names
+- #address-cells : must be set to 2
+- #size-cells : must be set to 0
+- qcom,ee : indicates the active Execution Environment identifier (0-5)
+- qcom,channel : which of the PMIC Arb provided channels to use for accesses (0-5)
+- interrupts : interrupt list for the PMIC Arb controller, must contain a
+ single interrupt entry for the peripheral interrupt
+- interrupt-names : corresponding interrupt names for the interrupts
+ listed in the 'interrupts' property, must contain:
+ "periph_irq" - summary interrupt for PMIC peripherals
+- interrupt-controller : boolean indicator that the PMIC arbiter is an interrupt controller
+- #interrupt-cells : must be set to 4. Interrupts are specified as a 4-tuple:
+ cell 1: slave ID for the requested interrupt (0-15)
+ cell 2: peripheral ID for requested interrupt (0-255)
+ cell 3: the requested peripheral interrupt (0-7)
+ cell 4: interrupt flags indicating level-sense information, as defined in
+ dt-bindings/interrupt-controller/irq.h
+
+Example:
+
+ spmi {
+ compatible = "qcom,spmi-pmic-arb";
+ reg-names = "core", "intr", "cnfg";
+ reg = <0xfc4cf000 0x1000>,
+ <0xfc4cb000 0x1000>,
+ <0xfc4ca000 0x1000>;
+
+ interrupt-names = "periph_irq";
+ interrupts = <0 190 0>;
+
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation


\
 
 \ /
  Last update: 2014-02-12 21:41    [W:0.064 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site