lkml.org 
[lkml]   [2014]   [Dec]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v16 04/12] input: cyapa: add runtime power management interfaces support for the device
Hi Dudley,

On Thu, Dec 18, 2014 at 06:00:48PM +0800, Dudley Du wrote:
> Add runtime_suspend_scanrate_ms power management interfaces in device's
> power group, so users or applications can control the runtime power
> management strategy of trackpad device as their requirements.
> TEST=test on Chromebooks.
>
> Signed-off-by: Dudley Du <dudl@cypress.com>
> ---
> drivers/input/mouse/cyapa.c | 171 +++++++++++++++++++++++++++++++++++++++++++-
> drivers/input/mouse/cyapa.h | 4 ++
> 2 files changed, 174 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/input/mouse/cyapa.c b/drivers/input/mouse/cyapa.c
> index 73f6817..3bcfce3 100644
> --- a/drivers/input/mouse/cyapa.c
> +++ b/drivers/input/mouse/cyapa.c
> @@ -23,6 +23,7 @@
> #include <linux/mutex.h>
> #include <linux/slab.h>
> #include <linux/uaccess.h>
> +#include <linux/pm_runtime.h>
> #include "cyapa.h"
>
>
> @@ -327,6 +328,8 @@ static int cyapa_open(struct input_dev *input)
> }
>
> enable_irq(client->irq);
> + pm_runtime_set_active(&client->dev);
> + pm_runtime_enable(&client->dev);
> out:
> mutex_unlock(&cyapa->state_sync_lock);
> return error;
> @@ -340,8 +343,10 @@ static void cyapa_close(struct input_dev *input)
> mutex_lock(&cyapa->state_sync_lock);
>
> disable_irq(client->irq);
> + pm_runtime_disable(&client->dev);
> if (!CYAPA_BOOTLOADER(cyapa) && cyapa->ops->set_power_mode)
> cyapa->ops->set_power_mode(cyapa, PWR_MODE_OFF, 0);
> + pm_runtime_set_suspended(&client->dev);
>
> mutex_unlock(&cyapa->state_sync_lock);
> }
> @@ -542,6 +547,7 @@ static irqreturn_t cyapa_irq(int irq, void *dev_id)
> struct device *dev = &cyapa->client->dev;
> bool cont;
>
> + pm_runtime_get_sync(dev);
> if (device_may_wakeup(dev))
> pm_wakeup_event(dev, 0);
>
> @@ -572,6 +578,8 @@ static irqreturn_t cyapa_irq(int irq, void *dev_id)
> }
>
> out:
> + pm_runtime_mark_last_busy(dev);
> + pm_runtime_put_sync_autosuspend(dev);
> return IRQ_HANDLED;
> }
>
> @@ -665,6 +673,116 @@ static void cyapa_remove_power_wakeup_group(void *data)
> }
> #endif /* CONFIG_PM_SLEEP */
>
> +#ifdef CONFIG_PM_RUNTIME
> +static ssize_t cyapa_show_rt_suspend_scanrate(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct cyapa *cyapa = dev_get_drvdata(dev);
> + u8 pwr_cmd;
> + u16 sleep_time;
> + int error;
> +
> + error = mutex_lock_interruptible(&cyapa->state_sync_lock);
> + if (error)
> + return error;
> + pwr_cmd = cyapa->runtime_suspend_power_mode;
> + sleep_time = cyapa->runtime_suspend_sleep_time;
> + mutex_unlock(&cyapa->state_sync_lock);
> +
> + if (cyapa->gen == CYAPA_GEN3)
> + return scnprintf(buf, PAGE_SIZE, "%u\n",
> + cyapa_pwr_cmd_to_sleep_time(pwr_cmd));
> + return scnprintf(buf, PAGE_SIZE, "%u\n", sleep_time);
> +}
> +
> +static ssize_t cyapa_update_rt_suspend_scanrate(struct device *dev,
> + struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct cyapa *cyapa = dev_get_drvdata(dev);
> + u16 time;
> + int error;
> +
> + if (buf == NULL || count == 0 || kstrtou16(buf, 10, &time)) {
> + dev_err(dev, "invalid runtime suspend scanrate ms parameter\n");
> + return -EINVAL;
> + }
> +
> + /*
> + * When the suspend scanrate is changed, pm_runtime_get to resume
> + * a potentially suspended device, update to the new pwr_cmd
> + * and then pm_runtime_put to suspend into the new power mode.
> + */
> + pm_runtime_get_sync(dev);
> + error = mutex_lock_interruptible(&cyapa->state_sync_lock);
> + if (error)
> + return error;
> + cyapa->runtime_suspend_sleep_time = max_t(u16, time, 1000);
> + cyapa->runtime_suspend_power_mode =
> + cyapa_sleep_time_to_pwr_cmd(cyapa->runtime_suspend_sleep_time);
> + mutex_unlock(&cyapa->state_sync_lock);
> + pm_runtime_put_sync_autosuspend(dev);
> +
> + return count;
> +}
> +
> +static DEVICE_ATTR(runtime_suspend_scanrate_ms, S_IRUGO|S_IWUSR,
> + cyapa_show_rt_suspend_scanrate,
> + cyapa_update_rt_suspend_scanrate);
> +
> +static struct attribute *cyapa_power_runtime_entries[] = {
> + &dev_attr_runtime_suspend_scanrate_ms.attr,
> + NULL,
> +};
> +
> +static const struct attribute_group cyapa_power_runtime_group = {
> + .name = power_group_name,
> + .attrs = cyapa_power_runtime_entries,
> +};
> +
> +static void cyapa_remove_power_runtime_group(void *data)
> +{
> + struct cyapa *cyapa = data;
> +
> + sysfs_unmerge_group(&cyapa->client->dev.kobj,
> + &cyapa_power_runtime_group);
> +}
> +
> +static int cyapa_start_runtime(struct cyapa *cyapa)
> +{
> + struct device *dev = &cyapa->client->dev;
> + int error;
> +
> + cyapa->runtime_suspend_power_mode = PWR_MODE_IDLE;
> + cyapa->runtime_suspend_sleep_time =
> + cyapa_pwr_cmd_to_sleep_time(cyapa->runtime_suspend_power_mode);
> +
> + error = sysfs_merge_group(&dev->kobj, &cyapa_power_runtime_group);
> + if (error) {
> + dev_err(dev,
> + "failed to create power runtime group: %d\n", error);
> + return error;
> + }
> +
> + error = devm_add_action(dev, cyapa_remove_power_runtime_group, cyapa);
> + if (error) {
> + cyapa_remove_power_runtime_group(cyapa);
> + dev_err(dev,
> + "failed to add power runtime cleanup action: %d\n",
> + error);
> + return error;
> + }
> +
> + /* runtime is enabled until device is operational and opened. */
> + pm_runtime_set_suspended(dev);
> + pm_runtime_use_autosuspend(dev);
> + pm_runtime_set_autosuspend_delay(dev, AUTOSUSPEND_DELAY);
> +
> + return 0;
> +}
> +#endif /* CONFIG_PM_RUNTIME */
> +
> static int cyapa_probe(struct i2c_client *client,
> const struct i2c_device_id *dev_id)
> {
> @@ -725,6 +843,14 @@ static int cyapa_probe(struct i2c_client *client,
> }
> #endif /* CONFIG_PM_SLEEP */
>
> +#ifdef CONFIG_PM_RUNTIME
> + error = cyapa_start_runtime(cyapa);
> + if (error) {
> + dev_err(dev, "failed to start pm_runtime: %d\n", error);
> + return error;
> + }
> +#endif /* CONFIG_PM_RUNTIME */

Instead of using #ifdef here please provide a stub cyapa_start_runtime()
for cases when !CONFIG_PM_RUNTIME.

> +
> error = devm_request_threaded_irq(dev, client->irq,
> NULL, cyapa_irq,
> IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
> @@ -765,6 +891,7 @@ static int __maybe_unused cyapa_suspend(struct device *dev)
> if (error)
> return error;
>
> + pm_runtime_disable(dev);
> disable_irq(client->irq);
>
> /*
> @@ -781,6 +908,8 @@ static int __maybe_unused cyapa_suspend(struct device *dev)
> error);
> }
>
> + pm_runtime_set_suspended(dev);
> +

I do not believe we should be touching runtime suspend state during
system state transition.

> if (device_may_wakeup(dev))
> cyapa->irq_wake = (enable_irq_wake(client->irq) == 0);
>
> @@ -801,17 +930,57 @@ static int __maybe_unused cyapa_resume(struct device *dev)
> cyapa->irq_wake = false;
> }
>
> + pm_runtime_set_active(dev);
> +
> error = cyapa_reinitialize(cyapa);
> if (error)
> dev_warn(dev, "failed to reinitialize TP device: %d\n", error);
>
> enable_irq(client->irq);
>
> + pm_runtime_enable(dev);
> +
> mutex_unlock(&cyapa->state_sync_lock);
> return 0;
> }
>
> -static SIMPLE_DEV_PM_OPS(cyapa_pm_ops, cyapa_suspend, cyapa_resume);
> +#ifdef CONFIG_PM_RUNTIME
> +static int cyapa_runtime_suspend(struct device *dev)
> +{
> + struct cyapa *cyapa = dev_get_drvdata(dev);
> + int error;
> +
> + if (!CYAPA_BOOTLOADER(cyapa) && cyapa->ops->set_power_mode) {

Why do we need to check bootloader state? I'd rather we did not enable
runtime PM until we make sure device is out of bootloader.

> + error = cyapa->ops->set_power_mode(cyapa,
> + cyapa->runtime_suspend_power_mode,
> + cyapa->runtime_suspend_sleep_time);
> + if (error)
> + dev_warn(dev, "runtime suspend failed: %d\n", error);
> + }
> +
> + return 0;
> +}
> +
> +static int cyapa_runtime_resume(struct device *dev)
> +{
> + struct cyapa *cyapa = dev_get_drvdata(dev);
> + int error;
> +
> + if (!CYAPA_BOOTLOADER(cyapa) && cyapa->ops->set_power_mode) {
> + error = cyapa->ops->set_power_mode(cyapa,
> + PWR_MODE_FULL_ACTIVE, 0);
> + if (error)
> + dev_warn(dev, "runtime resume failed: %d\n", error);
> + }
> +
> + return 0;
> +}
> +#endif /* CONFIG_PM_RUNTIME */
> +
> +static const struct dev_pm_ops cyapa_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(cyapa_suspend, cyapa_resume)
> + SET_RUNTIME_PM_OPS(cyapa_runtime_suspend, cyapa_runtime_resume, NULL)
> +};
>
> static const struct i2c_device_id cyapa_id_table[] = {
> { "cyapa", 0 },
> diff --git a/drivers/input/mouse/cyapa.h b/drivers/input/mouse/cyapa.h
> index 4c09be4..922a473 100644
> --- a/drivers/input/mouse/cyapa.h
> +++ b/drivers/input/mouse/cyapa.h
> @@ -253,6 +253,10 @@ struct cyapa {
> /* power mode settings */
> u8 suspend_power_mode;
> u16 suspend_sleep_time;
> +#ifdef CONFIG_PM_RUNTIME
> + u8 runtime_suspend_power_mode;
> + u16 runtime_suspend_sleep_time;
> +#endif /* CONFIG_PM_RUNTIME */
> u8 dev_pwr_mode;
> u16 dev_sleep_time;
>
> --
> 1.9.1
>

--
Dmitry


\
 
 \ /
  Last update: 2014-12-30 02:41    [W:2.424 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site