lkml.org 
[lkml]   [2014]   [Dec]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/4] ARM: at91/dt: sama5: move NAND nodes into board dts/dtsi
Hi, Boris

On 12/5/2014 6:30 AM, Boris Brezillon wrote:
> sama5d3 and sama5d4 SoCs provides several CS to interface with external
> memories, and in particular NAND chips.
> The NAND flash controller embedded in the these SoCs can connect to any of
> the available CS (each CS is assigned a memory range, hence the nand@xxx
> you're seeing in the DT), thus the NAND chip definition should be part of
> the board description because we cannot guess at the SoC level which CS
> will be chosen by the board designer.
>
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> ---
> arch/arm/boot/dts/at91-sama5d3_xplained.dts | 18 +++++++++++++++++-
> arch/arm/boot/dts/at91-sama5d4ek.dts | 16 +++++++++++++++-
> arch/arm/boot/dts/sama5d3.dtsi | 21 ---------------------
> arch/arm/boot/dts/sama5d3xcm.dtsi | 18 +++++++++++++++++-
> arch/arm/boot/dts/sama5d4.dtsi | 19 -------------------
> 5 files changed, 49 insertions(+), 43 deletions(-)
>
> diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
> index fec1fca..860258b 100644
> --- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
> +++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
> @@ -213,13 +213,29 @@
> };
>
> nand0: nand@60000000 {
> + compatible = "atmel,at91rm9200-nand";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
it would be better to leave this part to the sama5d3.dtsi.

> + reg = < 0x60000000 0x01000000 /* EBI CS3 */
> + 0xffffc070 0x00000490 /* SMC PMECC regs */
> + 0xffffc500 0x00000100 /* SMC PMECC Error Location regs */
> + 0x00110000 0x00018000 /* ROM code */
> + >;
> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 6>;
ditto.
> + atmel,nand-addr-offset = <21>;
> + atmel,nand-cmd-offset = <22>;
> + atmel,nand-has-dma;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_nand0_ale_cle>;
> + atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
ditto.

> + atmel,nfc = <&nfc>;
> nand-bus-width = <8>;
> nand-ecc-mode = "hw";
> atmel,has-pmecc;
> atmel,pmecc-cap = <4>;
> atmel,pmecc-sector-size = <512>;
> nand-on-flash-bbt;
> - status = "okay";
>
> at91bootstrap@0 {
> label = "at91bootstrap";
> diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts
> index b5b8400..5de0d2d 100644
> --- a/arch/arm/boot/dts/at91-sama5d4ek.dts
> +++ b/arch/arm/boot/dts/at91-sama5d4ek.dts
> @@ -204,11 +204,25 @@
> };
>
> nand0: nand@80000000 {
> + compatible = "atmel,at91rm9200-nand";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
it would be better to leave this part to the sama5d4.dtsi.

> + reg = < 0x80000000 0x08000000 /* EBI CS3 */
> + 0xfc05c070 0x00000490 /* SMC PMECC regs */
> + 0xfc05c500 0x00000100 /* SMC PMECC Error Location regs */
> + >;
> + interrupts = <22 IRQ_TYPE_LEVEL_HIGH 6>;
ditto.

> + atmel,nand-addr-offset = <21>;
> + atmel,nand-cmd-offset = <22>;
> + atmel,nand-has-dma;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_nand>;
> + atmel,nfc = <&nfc>;
> nand-bus-width = <8>;
> nand-ecc-mode = "hw";
> nand-on-flash-bbt;
> atmel,has-pmecc;
> - status = "okay";
>
> at91bootstrap@0 {
> label = "at91bootstrap";
> diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
> index 1749853..0a944e0 100644
> --- a/arch/arm/boot/dts/sama5d3.dtsi
> +++ b/arch/arm/boot/dts/sama5d3.dtsi
> @@ -1397,27 +1397,6 @@
> status = "disabled";
> };
>
> - nand0: nand@60000000 {
> - compatible = "atmel,at91rm9200-nand";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> - reg = < 0x60000000 0x01000000 /* EBI CS3 */
> - 0xffffc070 0x00000490 /* SMC PMECC regs */
> - 0xffffc500 0x00000100 /* SMC PMECC Error Location regs */
> - 0x00110000 0x00018000 /* ROM code */
> - >;
> - interrupts = <5 IRQ_TYPE_LEVEL_HIGH 6>;
> - atmel,nand-addr-offset = <21>;
> - atmel,nand-cmd-offset = <22>;
> - atmel,nand-has-dma;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_nand0_ale_cle>;
> - atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
> - atmel,nfc = <&nfc>;
> - status = "disabled";
> - };
> -
> nfc: nfc@70000000 {
> compatible = "atmel,sama5d3-nfc";
> reg = <0x70000000 0x10000000 /* NFC Command Registers */
> diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi
> index cfcd200..e6c2aec 100644
> --- a/arch/arm/boot/dts/sama5d3xcm.dtsi
> +++ b/arch/arm/boot/dts/sama5d3xcm.dtsi
> @@ -76,13 +76,29 @@
> };
>
> nand0: nand@60000000 {
> + compatible = "atmel,at91rm9200-nand";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
it would be better to leave this part to the sama5d3.dtsi.

> + reg = < 0x60000000 0x01000000 /* EBI CS3 */
> + 0xffffc070 0x00000490 /* SMC PMECC regs */
> + 0xffffc500 0x00000100 /* SMC PMECC Error Location regs */
> + 0x00110000 0x00018000 /* ROM code */
> + >;
> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 6>;
ditto.
> + atmel,nand-addr-offset = <21>;
> + atmel,nand-cmd-offset = <22>;
> + atmel,nand-has-dma;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_nand0_ale_cle>;
> + atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
ditto.

> + atmel,nfc = <&nfc>;
> nand-bus-width = <8>;
> nand-ecc-mode = "hw";
> atmel,has-pmecc;
> atmel,pmecc-cap = <4>;
> atmel,pmecc-sector-size = <512>;
> nand-on-flash-bbt;
> - status = "okay";
>
> at91bootstrap@0 {
> label = "at91bootstrap";
> diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
> index 3b5e9f1..8647eb3 100644
> --- a/arch/arm/boot/dts/sama5d4.dtsi
> +++ b/arch/arm/boot/dts/sama5d4.dtsi
> @@ -265,25 +265,6 @@
> cache-level = <2>;
> };
>
> - nand0: nand@80000000 {
> - compatible = "atmel,at91rm9200-nand";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> - reg = < 0x80000000 0x08000000 /* EBI CS3 */
> - 0xfc05c070 0x00000490 /* SMC PMECC regs */
> - 0xfc05c500 0x00000100 /* SMC PMECC Error Location regs */
> - >;
> - interrupts = <22 IRQ_TYPE_LEVEL_HIGH 6>;
> - atmel,nand-addr-offset = <21>;
> - atmel,nand-cmd-offset = <22>;
> - atmel,nand-has-dma;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_nand>;
> - atmel,nfc = <&nfc>;
> - status = "disabled";
> - };
> -
> nfc: nfc@90000000 {
> compatible = "atmel,sama5d3-nfc";
> reg = <0x90000000 0x10000000 /* NFC Command Registers */
Best Regards,
Josh Wu


\
 
 \ /
  Last update: 2014-12-26 11:21    [W:0.083 / U:2.464 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site