lkml.org 
[lkml]   [2014]   [Dec]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V2 2/2] ARM: dra7xx: Fix counter frequency drift for AM572x errata i856.
Hi Len,
On Wednesday 17 December 2014 02:38 AM, Lennart Sorensen wrote:
> Errata i856 for the AM572x (DRA7xx) points out that the 32.768KHz external
> crystal is not enabled at power up. Instead the CPU falls back to using
> an emulation for the 32KHz clock which is SYSCLK1/610. SYSCLK1 is usually
> 20MHz on boards so far (which gives an emulated frequency of 32.786KHz),
> but can also be 19.2 or 27MHz which result in much larger drift.
>
> Since this is used to drive the master counter at 32.768KHz * 375 /
> 2 = 6.144MHz, the emulated speed for 20MHz is of by 570ppm, or about 43
> seconds per day, and more than the 500ppm NTP is able to tolerate.
>
> Checking the CTRL_CORE_BOOTSTRAP register can determine if the CPU
> is using the real 32.768KHz crystal or the emulated SYSCLK1/610, and
> by known that the real counter frequency can be determined and used.
> The real speed is then SYSCLK1 / 610 * 375 / 2 or SYSCLK1 * 75 / 244.
Looks good to me.
Tested this on DRA7 evm.

Tested-by: Lokesh Vutla <lokeshvutla@ti.com>

Thanks and regards,
Lokesh

>
> Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
> ---
> arch/arm/mach-omap2/control.h | 4 ++++
> arch/arm/mach-omap2/timer.c | 36 ++++++++++++++++++++++++++++++++++--
> 2 files changed, 38 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/control.h b/arch/arm/mach-omap2/control.h
> index a3c0133..a80ac2d 100644
> --- a/arch/arm/mach-omap2/control.h
> +++ b/arch/arm/mach-omap2/control.h
> @@ -286,6 +286,10 @@
> #define OMAP5XXX_CONTROL_STATUS 0x134
> #define OMAP5_DEVICETYPE_MASK (0x7 << 6)
>
> +/* DRA7XX CONTROL CORE BOOTSTRAP */
> +#define DRA7_CTRL_CORE_BOOTSTRAP 0x6c4
> +#define DRA7_SPEEDSELECT_MASK (0x3 << 8)
> +
> /*
> * REVISIT: This list of registers is not comprehensive - there are more
> * that should be added.
> diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
> index fb0cb2b..7d45c84 100644
> --- a/arch/arm/mach-omap2/timer.c
> +++ b/arch/arm/mach-omap2/timer.c
> @@ -54,6 +54,7 @@
>
> #include "soc.h"
> #include "common.h"
> +#include "control.h"
> #include "powerdomain.h"
> #include "omap-secure.h"
>
> @@ -496,7 +497,8 @@ static void __init realtime_counter_init(void)
> void __iomem *base;
> static struct clk *sys_clk;
> unsigned long rate;
> - unsigned int reg, num, den;
> + unsigned int reg;
> + unsigned long long num, den;
>
> base = ioremap(REALTIME_COUNTER_BASE, SZ_32);
> if (!base) {
> @@ -511,6 +513,35 @@ static void __init realtime_counter_init(void)
> }
>
> rate = clk_get_rate(sys_clk);
> +
> + if (soc_is_dra7xx()) {
> + /*
> + * Errata i856 says the 32.768KHz crystal does not start at
> + * power on, so the CPU falls back to an emulated 32KHz clock
> + * based on sysclk / 610 instead. This causes the master counter
> + * frequency to not be 6.144MHz but at sysclk / 610 * 375 / 2
> + * (OR sysclk * 75 / 244)
> + *
> + * This affects at least the DRA7/AM572x 1.0, 1.1 revisions.
> + * Of course any board built without a populated 32.768KHz
> + * crystal would also need this fix even if the CPU is fixed
> + * later.
> + *
> + * Either case can be detected by using the two speedselect bits
> + * If they are not 0, then the 32.768KHz clock driving the
> + * coarse counter that corrects the fine counter every time it
> + * ticks is actually rate/610 rather than 32.768KHz and we
> + * should compensate to avoid the 570ppm (at 20MHz, much worse
> + * at other rates) too fast system time.
> + */
> + reg = omap_ctrl_readl(DRA7_CTRL_CORE_BOOTSTRAP);
> + if (reg & DRA7_SPEEDSELECT_MASK) {
> + num = 75;
> + den = 244;
> + goto sysclk1_based;
> + }
> + }
> +
> /* Numerator/denumerator values refer TRM Realtime Counter section */
> switch (rate) {
> case 12000000:
> @@ -545,6 +576,7 @@ static void __init realtime_counter_init(void)
> break;
> }
>
> +sysclk1_based:
> /* Program numerator and denumerator registers */
> reg = readl_relaxed(base + INCREMENTER_NUMERATOR_OFFSET) &
> NUMERATOR_DENUMERATOR_MASK;
> @@ -556,7 +588,7 @@ static void __init realtime_counter_init(void)
> reg |= den;
> writel_relaxed(reg, base + INCREMENTER_DENUMERATOR_RELOAD_OFFSET);
>
> - arch_timer_freq = (rate / den) * num;
> + arch_timer_freq = DIV_ROUND_UP_ULL(rate * num, den);
> set_cntfreq();
>
> iounmap(base);
>



\
 
 \ /
  Last update: 2014-12-17 10:21    [W:1.692 / U:1.372 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site