lkml.org 
[lkml]   [2014]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v7 1/5] hwmon: ina2xx: reinitialize the chip in case it's been reset
Date
Chips from the ina family don't like to be uninitialized. In case the power
is cut-off and restored again the calibration register will be reset
to 0 and both the power and current registers will remain at 0.

Check the calibration register in ina2xx_update_device() and reinitialize
the chip if needed.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
drivers/hwmon/ina2xx.c | 128 +++++++++++++++++++++++++++++++++++--------------
1 file changed, 91 insertions(+), 37 deletions(-)

diff --git a/drivers/hwmon/ina2xx.c b/drivers/hwmon/ina2xx.c
index e01feba..ffbd60f 100644
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -35,6 +35,7 @@
#include <linux/hwmon-sysfs.h>
#include <linux/jiffies.h>
#include <linux/of.h>
+#include <linux/delay.h>

#include <linux/platform_data/ina2xx.h>

@@ -64,6 +65,9 @@

/* worst case is 68.10 ms (~14.6Hz, ina219) */
#define INA2XX_CONVERSION_RATE 15
+#define INA2XX_MAX_DELAY 69 /* worst case delay in ms */
+
+#define INA2XX_RSHUNT_DEFAULT 10000

enum ina2xx_ids { ina219, ina226 };

@@ -81,6 +85,8 @@ struct ina2xx_data {
struct i2c_client *client;
const struct ina2xx_config *config;

+ long rshunt;
+
struct mutex update_lock;
bool valid;
unsigned long last_updated;
@@ -110,34 +116,96 @@ static const struct ina2xx_config ina2xx_config[] = {
},
};

-static struct ina2xx_data *ina2xx_update_device(struct device *dev)
+/*
+ * Initialize the configuration and calibration registers.
+ */
+static int ina2xx_init(struct ina2xx_data *data)
{
- struct ina2xx_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
- struct ina2xx_data *ret = data;
+ int ret;

- mutex_lock(&data->update_lock);
+ /* device configuration */
+ ret = i2c_smbus_write_word_swapped(client, INA2XX_CONFIG,
+ data->config->config_default);
+ if (ret < 0)
+ return ret;

- if (time_after(jiffies, data->last_updated +
- HZ / INA2XX_CONVERSION_RATE) || !data->valid) {
+ /*
+ * Set current LSB to 1mA, shunt is in uOhms
+ * (equation 13 in datasheet).
+ */
+ return i2c_smbus_write_word_swapped(client, INA2XX_CALIBRATION,
+ data->config->calibration_factor / data->rshunt);
+}

- int i;
+static int ina2xx_do_update(struct device *dev)
+{
+ struct ina2xx_data *data = dev_get_drvdata(dev);
+ struct i2c_client *client = data->client;
+ int i, rv, retry;

- dev_dbg(&client->dev, "Starting ina2xx update\n");
+ dev_dbg(&client->dev, "Starting ina2xx update\n");

+ for (retry = 5; retry; retry--) {
/* Read all registers */
for (i = 0; i < data->config->registers; i++) {
- int rv = i2c_smbus_read_word_swapped(client, i);
- if (rv < 0) {
- ret = ERR_PTR(rv);
- goto abort;
- }
+ rv = i2c_smbus_read_word_swapped(client, i);
+ if (rv < 0)
+ return rv;
data->regs[i] = rv;
}
+
+ /*
+ * If the current value in the calibration register is 0, the
+ * power and current registers will also remain at 0. In case
+ * the chip has been reset let's check the calibration
+ * register and reinitialize if needed.
+ */
+ if (data->regs[INA2XX_CALIBRATION] == 0) {
+ dev_warn(dev, "chip not calibrated, reinitializing\n");
+
+ rv = ina2xx_init(data);
+ if (rv < 0)
+ return rv;
+
+ /*
+ * Let's make sure the power and current registers
+ * have been updated before trying again.
+ */
+ msleep(INA2XX_MAX_DELAY);
+ continue;
+ }
+
data->last_updated = jiffies;
data->valid = 1;
+
+ return 0;
}
-abort:
+
+ /*
+ * If we're here then although all write operations succeeded, the
+ * chip still returns 0 in the calibration register. Nothing more we
+ * can do here.
+ */
+ dev_err(dev, "unable to reinitialize the chip\n");
+ return -ENODEV;
+}
+
+static struct ina2xx_data *ina2xx_update_device(struct device *dev)
+{
+ struct ina2xx_data *data = dev_get_drvdata(dev);
+ struct ina2xx_data *ret = data;
+ int rv;
+
+ mutex_lock(&data->update_lock);
+
+ if (time_after(jiffies, data->last_updated +
+ HZ / INA2XX_CONVERSION_RATE) || !data->valid) {
+ rv = ina2xx_do_update(dev);
+ if (rv < 0)
+ ret = ERR_PTR(rv);
+ }
+
mutex_unlock(&data->update_lock);
return ret;
}
@@ -221,7 +289,6 @@ static int ina2xx_probe(struct i2c_client *client,
struct device *dev = &client->dev;
struct ina2xx_data *data;
struct device *hwmon_dev;
- long shunt = 10000; /* default shunt value 10mOhms */
u32 val;
int ret;

@@ -234,41 +301,28 @@ static int ina2xx_probe(struct i2c_client *client,

if (dev_get_platdata(dev)) {
pdata = dev_get_platdata(dev);
- shunt = pdata->shunt_uohms;
+ data->rshunt = pdata->shunt_uohms;
} else if (!of_property_read_u32(dev->of_node,
"shunt-resistor", &val)) {
- shunt = val;
+ data->rshunt = val;
+ } else {
+ data->rshunt = INA2XX_RSHUNT_DEFAULT;
}

- if (shunt <= 0)
- return -ENODEV;
-
/* set the device type */
data->kind = id->driver_data;
data->config = &ina2xx_config[data->kind];
+ data->client = client;

- /* device configuration */
- ret = i2c_smbus_write_word_swapped(client, INA2XX_CONFIG,
- data->config->config_default);
- if (ret < 0) {
- dev_err(dev,
- "error writing to the config register: %d", ret);
+ if (data->rshunt <= 0)
return -ENODEV;
- }

- /*
- * Set current LSB to 1mA, shunt is in uOhms
- * (equation 13 in datasheet).
- */
- ret = i2c_smbus_write_word_swapped(client, INA2XX_CALIBRATION,
- data->config->calibration_factor / shunt);
+ ret = ina2xx_init(data);
if (ret < 0) {
- dev_err(dev,
- "error writing to the calibration register: %d", ret);
+ dev_err(dev, "error configuring the device: %d\n", ret);
return -ENODEV;
}

- data->client = client;
mutex_init(&data->update_lock);

hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
@@ -277,7 +331,7 @@ static int ina2xx_probe(struct i2c_client *client,
return PTR_ERR(hwmon_dev);

dev_info(dev, "power monitor %s (Rshunt = %li uOhm)\n",
- id->name, shunt);
+ id->name, data->rshunt);

return 0;
}
--
2.1.3


\
 
 \ /
  Last update: 2014-12-13 18:01    [W:0.448 / U:0.672 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site