lkml.org 
[lkml]   [2014]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2] PCI: pciehp: Check link state before accessing device during removal
On Thu, Dec 11, 2014 at 9:38 AM, Guenter Roeck <groeck@juniper.net> wrote:
> On Wed, Dec 10, 2014 at 05:26:30PM -0700, Bjorn Helgaas wrote:
>> On Thu, Nov 20, 2014 at 02:54:24PM -0800, Rajat Jain wrote:
>> > While removing a card, we can't assume the presence to mean that the
>> > access to card is OK. That is because the cause of removal may be a
>> > link down event, and the card may still be physically present. Thus,
>> > instead of presence, use the link state to decide whether or not it is
>> > OK to access the card devices.
>> >
>> > Here are the problem symptoms:
>> > During the removal of a card due to link down, sometimes the following
>> > error is seen (because pciehp_unconfigure_device() reads 0xFF from
>> > bridge control register as the link is down, which cause it to assume
>> > that the VGA bit is set):
>> >
>> > pciehp 0000:21:05.0:pcie24: pcie_isr: intr_loc 100
>> > pciehp 0000:21:05.0:pcie24: Data Link Layer State change
>> > pciehp 0000:21:05.0:pcie24: slot(5): Link Down event
>> > pciehp 0000:21:05.0:pcie24: Disabling domain:bus:device=0000:60:00
>> > pciehp 0000:21:05.0:pcie24: pciehp_unconfigure_device: domain:bus:dev = 0000:60:00
>> > pciehp 0000:21:05.0:pcie24: Cannot remove display device 0000:60:00.0
>> >
>> > Ofcourse, when the link comes back up, the device addition fails too:
>> >
>> > pciehp 0000:21:05.0:pcie24: pcie_isr: intr_loc 100
>> > pciehp 0000:21:05.0:pcie24: Data Link Layer State change
>> > pciehp 0000:21:05.0:pcie24: pciehp_check_link_active: lnk_status = 6011
>> > pciehp 0000:21:05.0:pcie24: slot(5): Link Up event
>> > pciehp 0000:21:05.0:pcie24: Enabling domain:bus:device=0000:60:00
>> > pciehp 0000:21:05.0:pcie24: pciehp_check_link_active: lnk_status = 6011
>> > pciehp 0000:21:05.0:pcie24: pciehp_check_link_status: lnk_status = 6011
>> > pciehp 0000:21:05.0:pcie24: Device 0000:60:00.0 already exists at 0000:60:00, cannot hot-add
>> > pciehp 0000:21:05.0:pcie24: Cannot add device at 0000:60:00
>> >
>> > The problem is not seen with this patch applied. The device removal and
>> > insertion works as expected.
>> >
>> > Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
>> > Signed-off-by: Rajat Jain <rajatjain@juniper.net>
>> > Signed-off-by: Guenter Roeck <groeck@juniper.net>
>> > ---
>> > v2: Use the already initialized "ctrl" instead of "p_slot->ctrl"
>> >
>> > drivers/pci/hotplug/pciehp_pci.c | 8 ++++----
>> > 1 file changed, 4 insertions(+), 4 deletions(-)
>> >
>> > diff --git a/drivers/pci/hotplug/pciehp_pci.c b/drivers/pci/hotplug/pciehp_pci.c
>> > index 9e69403..911f85b 100644
>> > --- a/drivers/pci/hotplug/pciehp_pci.c
>> > +++ b/drivers/pci/hotplug/pciehp_pci.c
>> > @@ -77,7 +77,7 @@ int pciehp_unconfigure_device(struct slot *p_slot)
>> > {
>> > int rc = 0;
>> > u8 bctl = 0;
>> > - u8 presence = 0;
>> > + bool link_active = false;
>> > struct pci_dev *dev, *temp;
>> > struct pci_bus *parent = p_slot->ctrl->pcie->port->subordinate;
>> > u16 command;
>> > @@ -85,7 +85,7 @@ int pciehp_unconfigure_device(struct slot *p_slot)
>> >
>> > ctrl_dbg(ctrl, "%s: domain:bus:dev = %04x:%02x:00\n",
>> > __func__, pci_domain_nr(parent), parent->number);
>> > - pciehp_get_adapter_status(p_slot, &presence);
>> > + link_active = pciehp_check_link_active(ctrl);
>> >
>> > pci_lock_rescan_remove();
>> >
>> > @@ -98,7 +98,7 @@ int pciehp_unconfigure_device(struct slot *p_slot)
>> > list_for_each_entry_safe_reverse(dev, temp, &parent->devices,
>> > bus_list) {
>> > pci_dev_get(dev);
>> > - if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE && presence) {
>> > + if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE && link_active) {
>> > pci_read_config_byte(dev, PCI_BRIDGE_CONTROL, &bctl);
>> > if (bctl & PCI_BRIDGE_CTL_VGA) {
>> > ctrl_err(ctrl,
>>
>> Why do we even have this code to check for VGA devices? I looked (briefly)
>> and couldn't find anything in the spec that prohibits removal of VGA
>> devices.
>>
> For my part I don't know. I only know that I had to integrate the patch into
> our images since I hit the problem repeatedly. Usually I wait with integrating
> Rajat's patches until you accept them, but this one was too disruptive.
>
> I would argue that while the patch may not be perfect, at least it improves
> the situation substantially.

I don't think removing the VGA checks is the way to fix the problem
you're seeing. But I do want to investigate this code since we're in
the area.

>> If we do need it (and it looks like most or all hotplug drivers copied it),
>> isn't there still a race? Can't we have the following sequence?
>>
>> - pciehp_check_link_active() # returns true
>> - Link goes down
>> - pci_read_config_byte() # fails because link is down
>>
> I would guess so. Question is how to address it. Read the configuration byte
> first, then check if the link is down ? Check if link is still up after reading
> the configuration byte ? Add a note that there may be a potential race condition
> and do nothing until it is actually seen ?

I think we should just read PCI_BRIDGE_CONTROL and look for a 0xff
value. That's not a legal value for the register, so if we see it, it
should be pretty safe to assume the link is down or the device is not
present at all.

Bjorn


\
 
 \ /
  Last update: 2014-12-11 22:01    [W:0.121 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site