lkml.org 
[lkml]   [2014]   [Nov]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4/7] pinctrl: zynq: Document DT binding
Date
Add documentation for the devicetree binding for the Zynq pincontroller.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
---
.../bindings/pinctrl/xlnx,zynq-pinctrl.txt | 90 ++++++++++++++++++++++
1 file changed, 90 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt

diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt
new file mode 100644
index 000000000000..86a86b644e6c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt
@@ -0,0 +1,90 @@
+ Binding for Xilinx Zynq Pinctrl
+
+Required properties:
+- compatible: "xlnx,zynq-pinctrl"
+- syscon: phandle to SLCR
+- reg: Offset and length of pinctrl space in SLCR
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Zynq's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, slew rate, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+ groups, pins, function, bias-disable, bias-high-impedance, bias-pull-up,
+ slew-rate, low-power-disable, low-power-enable
+
+ Valid arguments for 'slew-rate' are '0' and '1' to select between slow and fast
+ respectively.
+
+ Valid values for groups are:
+ ethernet0_0_grp, ethernet1_0_grp, mdio0_0_grp, mdio1_0_grp,
+ qspi0_0_grp, qspi1_0_grp, qspi_fbclk, qspi_cs1_grp, spi0_0_grp,
+ spi0_1_grp - spi0_2_grp, spi1_0_grp - spi1_3_grp, sdio0_0_grp - sdio0_2_grp,
+ sdio1_0_grp - sdio1_3_grp, sdio0_emio_wp, sdio0_emio_cd, sdio1_emio_wp,
+ sdio1_emio_cd, smc0_nor, smc0_nor_cs1_grp, smc0_nor_addr25_grp, smc0_nand,
+ can0_0_grp - can0_10_grp, can1_0_grp - can1_11_grp, uart0_0_grp - uart0_10_grp,
+ uart1_0_grp - uart1_11_grp, i2c0_0_grp - i2c0_10_grp, i2c1_0_grp - i2c1_10_grp,
+ ttc0_0_grp - ttc0_2_grp, ttc1_0_grp - ttc1_2_grp, swdt0_0_grp - swdt0_4_grp,
+ gpio0_0_grp - gpio0_53_grp
+
+ Valid values for pins are:
+ MIO0 - MIO53
+
+ Valid values for function are:
+ ethernet0, ethernet1, mdio0, mdio1, qspi0, qspi1, qspi_fbclk, qspi_cs1,
+ spi0, spi1, sdio0, sdio0_pc, sdio0_cd, sdio0_wp,
+ sdio1, sdio1_pc, sdio1_cd, sdio1_wp,
+ smc0_nor, smc0_nor_cs1, smc0_nor_addr25, smc0_nand, can0, can1, uart0, uart1,
+ i2c0, i2c1, ttc0, ttc1, swdt0, gpio0
+
+The following driver-specific properties as defined here are valid to specify in
+a pin configuration subnode:
+ - io-standard: Configure the pin to use the selected IO standard according to
+ this mapping:
+ 1: LVCMOS18
+ 2: LVCMOS25
+ 3: LVCMOS33
+ 4: HSTL
+
+Example:
+ pinctrl0: pinctrl@700 {
+ compatible = "xlnx,pinctrl-zynq";
+ reg = <0x700 0x200>;
+ syscon = <&slcr>;
+
+ pinctrl_uart1_default: pinctrl-uart1-default {
+ common {
+ groups = "uart1_10_grp";
+ function = "uart1";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ rx {
+ pins = "MIO49";
+ bias-high-impedance;
+ };
+
+ tx {
+ pins = "MIO48";
+ bias-disable;
+ };
+ };
+ };
--
1.9.1


\
 
 \ /
  Last update: 2014-11-03 20:41    [W:0.205 / U:0.948 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site