lkml.org 
[lkml]   [2014]   [Nov]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V4] arm64: amd-seattle: Adding device tree for AMD Seattle platform
On 27/11/14 14:28, Liviu Dudau wrote:
> On Tue, Nov 25, 2014 at 11:46:50AM +0000, Suthikulpanit, Suravee wrote:
>> Hi Marc,
>>
>> On 11/25/14, 17:23, "Marc Zyngier" <marc.zyngier@arm.com> wrote:
>>
>>> Hi Suravee,
>>>
>>> Just spotted a small issue below (looks like a recurring mistake in a
>>> number of DTs I've seem lately):
>>>
>>> On 24/11/14 21:51, suravee.suthikulpanit@amd.com wrote:
>>>> From: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
>>>>
>>>> Initial revision of device tree for AMD Seattle platform.
>>>>
>>>> Cc: Arnd Bergmann <arnd@arndb.de>
>>>> Cc: Marc Zyngier <marc.zyngier@arm.com>
>>>> Cc: Mark Rutland <mark.rutland@arm.com>
>>>> Cc: Will Deacon <will.deacon@arm.com>
>>>> Cc: Catalin Marinas <catalin.marinas@arm.com>
>>>> Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
>>>> Signed-off-by: Thomas Lendacky <Thomas.Lendacky@amd.com>
>>>> Signed-off-by: Joel Schopp <Joel.Schopp@amd.com>
>>>> ---
>>>> V4 Changes:
>>>> * Remove unnecessary smb layer and move motherbord to top level
>>>> * Move include dtsi to top level
>>>> * Remove apb_pclk from sata0 and i2c
>>>> * Fix GIC Virtual Maintanance Interrupt from PPI24 (8) to PPI25 (9)
>>>> * Add 40-bit dma-ranges for motherboard (simple-bus)
>>>> * Remove dma0 (pl330) entry for now since it only supports 32-bit
>>>> DMA.
>>>> It is basically not used at the moment. It would also need SMMU
>>>> to allow dma remapping to 40-bit DMA range.
>>>> * Add phandle spi0 and spi1
>>>> * Hook up gpio0 pin 7 with MMC Card Detection (CD) support.
>>>> * Changes in pcie0 entry:
>>>> - Add 40-bit dma-ranges
>>>> - Remove interrupts property
>>>> - Add interrupt-map/mask property
>>>> - Fix PCI I/O range
>>>> - Merge PCI 32-bit ranges
>>>> - Merge PCI 64-bit ranges
>>>>
>>>> NOTE: I am not add a new compatible ID for the sata0 as Rob Herring
>>>> suggested since there is no need at the momement, and I am trying
>>>> to avoid introducing ID unnecessarily.
>>>>
>>>> arch/arm64/Kconfig | 5 +
>>>> arch/arm64/boot/dts/Makefile | 1 +
>>>> arch/arm64/boot/dts/amd-seattle-periph.dtsi | 156
>>>> ++++++++++++++++++++++++++++
>>>> arch/arm64/boot/dts/amd-seattle.dts | 89 ++++++++++++++++
>>>> 4 files changed, 251 insertions(+)
>>>> create mode 100644 arch/arm64/boot/dts/amd-seattle-periph.dtsi
>>>> create mode 100644 arch/arm64/boot/dts/amd-seattle.dts
>>>>
>>>
>>> [...]
>>>
>>>> diff --git a/arch/arm64/boot/dts/amd-seattle.dts
>>>> b/arch/arm64/boot/dts/amd-seattle.dts
>>>> new file mode 100644
>>>> index 0000000..d5fc482
>>>> --- /dev/null
>>>> +++ b/arch/arm64/boot/dts/amd-seattle.dts
>>>> @@ -0,0 +1,89 @@
>>>> +/*
>>>> + * DTS file for AMD Seattle
>>>> + *
>>>> + * Copyright (C) 2014 Advanced Micro Devices, Inc.
>>>> + */
>>>> +
>>>> +/dts-v1/;
>>>> +
>>
>> [...]
>>
>>>> +
>>>> + timer {
>>>> + compatible = "arm,armv8-timer";
>>>> + interrupts = <1 13 0xff01>,
>>>> + <1 14 0xff01>,
>>>> + <1 11 0xff01>,
>>>> + <1 10 0xff01>;
>>>> + };
>>>
>>> The Cortex-A57 TRM clearly states that these interrupts are level
>>> triggered.
>>
>> Thanks for pointing this out. I¹ll fix this to <1 1X 0xff04> (4 for the
>> Active-High) then.
>
> Hi Suravee,
>
> Don't know what Seattle does, but the TRM says that the outputs are active-LOW.

As I said in another thread, 0xff04 *is* the right value. This is an
interrupt descriptor for the GIC, not a qualifier for the signal that
comes out of the core.

Thanks.

M.
--
Jazz is not dead. It just smells funny...


\
 
 \ /
  Last update: 2014-11-27 16:21    [W:0.041 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site