lkml.org 
[lkml]   [2014]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V4] arm64: amd-seattle: Adding device tree for AMD Seattle platform
Date
From: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>

Initial revision of device tree for AMD Seattle platform.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Thomas Lendacky <Thomas.Lendacky@amd.com>
Signed-off-by: Joel Schopp <Joel.Schopp@amd.com>
---
V4 Changes:
* Remove unnecessary smb layer and move motherbord to top level
* Move include dtsi to top level
* Remove apb_pclk from sata0 and i2c
* Fix GIC Virtual Maintanance Interrupt from PPI24 (8) to PPI25 (9)
* Add 40-bit dma-ranges for motherboard (simple-bus)
* Remove dma0 (pl330) entry for now since it only supports 32-bit DMA.
It is basically not used at the moment. It would also need SMMU
to allow dma remapping to 40-bit DMA range.
* Add phandle spi0 and spi1
* Hook up gpio0 pin 7 with MMC Card Detection (CD) support.
* Changes in pcie0 entry:
- Add 40-bit dma-ranges
- Remove interrupts property
- Add interrupt-map/mask property
- Fix PCI I/O range
- Merge PCI 32-bit ranges
- Merge PCI 64-bit ranges

NOTE: I am not add a new compatible ID for the sata0 as Rob Herring
suggested since there is no need at the momement, and I am trying
to avoid introducing ID unnecessarily.

arch/arm64/Kconfig | 5 +
arch/arm64/boot/dts/Makefile | 1 +
arch/arm64/boot/dts/amd-seattle-periph.dtsi | 156 ++++++++++++++++++++++++++++
arch/arm64/boot/dts/amd-seattle.dts | 89 ++++++++++++++++
4 files changed, 251 insertions(+)
create mode 100644 arch/arm64/boot/dts/amd-seattle-periph.dtsi
create mode 100644 arch/arm64/boot/dts/amd-seattle.dts

diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
index 9532f8d..ddc0196 100644
--- a/arch/arm64/Kconfig
+++ b/arch/arm64/Kconfig
@@ -142,6 +142,11 @@ source "kernel/Kconfig.freezer"

menu "Platform selection"

+config ARCH_SEATTLE
+ bool "AMD Seattle SoC Family"
+ help
+ This enables support for AMD Seattle SOC Family
+
config ARCH_THUNDER
bool "Cavium Inc. Thunder SoC Family"
help
diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
index f8001a6..604af09 100644
--- a/arch/arm64/boot/dts/Makefile
+++ b/arch/arm64/boot/dts/Makefile
@@ -1,3 +1,4 @@
+dtb-$(CONFIG_ARCH_SEATTLE) += amd-seattle.dtb
dtb-$(CONFIG_ARCH_THUNDER) += thunder-88xx.dtb
dtb-$(CONFIG_ARCH_VEXPRESS) += rtsm_ve-aemv8a.dtb foundation-v8.dtb
dtb-$(CONFIG_ARCH_XGENE) += apm-mustang.dtb
diff --git a/arch/arm64/boot/dts/amd-seattle-periph.dtsi b/arch/arm64/boot/dts/amd-seattle-periph.dtsi
new file mode 100644
index 0000000..77f565b
--- /dev/null
+++ b/arch/arm64/boot/dts/amd-seattle-periph.dtsi
@@ -0,0 +1,156 @@
+/*
+ * DTS file for AMD Seattle Peripheral
+ *
+ * Copyright (C) 2014 Advanced Micro Devices, Inc.
+ */
+
+/ {
+ motherboard {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0 0 0 0xe0000000 0 0x01300000>;
+
+ /* DDR range is 40-bit addressing */
+ dma-ranges = <0x80 0x0 0x80 0x0 0x7f 0xffffffff>;
+
+ adl3clk_100mhz: clk100mhz_0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "adl3clk_100mhz";
+ };
+
+ ccpclk_375mhz: clk375mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <375000000>;
+ clock-output-names = "ccpclk_375mhz";
+ };
+
+ sataclk_333mhz: clk333mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <333000000>;
+ clock-output-names = "sataclk_333mhz";
+ };
+
+ pcieclk_500mhz: clk500mhz_0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <500000000>;
+ clock-output-names = "pcieclk_500mhz";
+ };
+
+ dmaclk_500mhz: clk500mhz_1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <500000000>;
+ clock-output-names = "dmaclk_500mhz";
+ };
+
+ miscclk_250mhz: clk250mhz_4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <250000000>;
+ clock-output-names = "miscclk_250mhz";
+ };
+
+ uartspiclk_100mhz: clk100mhz_1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "uartspiclk_100mhz";
+ };
+
+ sata0: sata@00300000 {
+ compatible = "snps,dwc-ahci";
+ reg = <0 0x300000 0 0x800>;
+ interrupts = <0 355 4>;
+ clocks = <&sataclk_333mhz>;
+ dma-coherent;
+ };
+
+ i2c@1000000 {
+ compatible = "snps,designware-i2c";
+ reg = <0 0x01000000 0 0x1000>;
+ interrupts = <0 357 4>;
+ clocks = <&uartspiclk_100mhz>;
+ };
+
+ serial0: serial@1010000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0 0x1010000 0 0x1000>;
+ interrupts = <0 328 4>;
+ clocks = <&uartspiclk_100mhz>, <&uartspiclk_100mhz>;
+ clock-names = "uartclk", "apb_pclk";
+ };
+
+ spi0: ssp@1020000 {
+ compatible = "arm,pl022", "arm,primecell";
+ #gpio-cells = <2>;
+ reg = <0 0x1020000 0 0x1000>;
+ spi-controller;
+ interrupts = <0 330 4>;
+ clocks = <&uartspiclk_100mhz>;
+ clock-names = "apb_pclk";
+ };
+
+ spi1: ssp@1030000 {
+ compatible = "arm,pl022", "arm,primecell";
+ #gpio-cells = <2>;
+ reg = <0 0x1030000 0 0x1000>;
+ spi-controller;
+ interrupts = <0 329 4>;
+ clocks = <&uartspiclk_100mhz>;
+ clock-names = "apb_pclk";
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sdcard@0 {
+ compatible = "mmc-spi-slot";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ voltage-ranges = <3200 3400>;
+ gpios = <&gpio0 7 0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 3>;
+ pl022,hierarchy = <0>;
+ pl022,interface = <0>;
+ pl022,com-mode = <0x0>;
+ pl022,rx-level-trig = <0>;
+ pl022,tx-level-trig = <0>;
+ };
+ };
+
+ gpio0: gpio@1040000 {
+ compatible = "arm,pl061", "arm,primecell";
+ #gpio-cells = <2>;
+ reg = <0 0x1040000 0 0x1000>;
+ gpio-controller;
+ interrupts = <0 359 4>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&uartspiclk_100mhz>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio1: gpio@1050000 {
+ compatible = "arm,pl061", "arm,primecell";
+ #gpio-cells = <2>;
+ reg = <0 0x1050000 0 0x1000>;
+ gpio-controller;
+ interrupts = <0 358 4>;
+ clocks = <&uartspiclk_100mhz>;
+ clock-names = "apb_pclk";
+ };
+
+ ccp: ccp@00100000 {
+ compatible = "amd,ccp-seattle-v1a";
+ reg = <0 0x00100000 0 0x10000>;
+ interrupts = <0 3 4>;
+ dma-coherent;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/amd-seattle.dts b/arch/arm64/boot/dts/amd-seattle.dts
new file mode 100644
index 0000000..d5fc482
--- /dev/null
+++ b/arch/arm64/boot/dts/amd-seattle.dts
@@ -0,0 +1,89 @@
+/*
+ * DTS file for AMD Seattle
+ *
+ * Copyright (C) 2014 Advanced Micro Devices, Inc.
+ */
+
+/dts-v1/;
+
+/include/ "amd-seattle-periph.dtsi"
+
+/ {
+ compatible = "amd,seattle";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen {
+ stdout-path = &serial0;
+ linux,pci-probe-only;
+ };
+
+ gic: interrupt-controller@e1101000 {
+ compatible = "arm,gic-400", "arm,cortex-a15-gic";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x0 0xe1110000 0 0x1000>,
+ <0x0 0xe112f000 0 0x2000>,
+ <0x0 0xe1140000 0 0x10000>,
+ <0x0 0xe1160000 0 0x10000>;
+ interrupts = <1 9 0xf04>;
+ ranges;
+ v2m0: v2m@e1180000 {
+ compatible = "arm,gic-v2m-frame";
+ msi-controller;
+ arm,msi-base-spi = <64>;
+ arm,msi-num-spis = <256>;
+ reg = <0x0 0xe1180000 0 0x1000>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <1 13 0xff01>,
+ <1 14 0xff01>,
+ <1 11 0xff01>,
+ <1 10 0xff01>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <0 7 4>,
+ <0 8 4>,
+ <0 9 4>,
+ <0 10 4>,
+ <0 11 4>,
+ <0 12 4>,
+ <0 13 4>,
+ <0 14 4>;
+ };
+
+ pcie0: pcie-controller {
+ compatible = "pci-host-ecam-generic";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ bus-range = <0 0xff>;
+ reg = <0 0xf0000000 0 0x10000000>;
+ msi-parent = <&v2m0>;
+
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <0x1000 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x120 0x1>,
+ <0x1000 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x121 0x1>,
+ <0x1000 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x122 0x1>,
+ <0x1000 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x123 0x1>;
+
+ dma-coherent;
+ dma-ranges = <0x43000000 0x80 0x0 0x80 0x0 0x7f 0xffffffff>;
+ ranges =
+ /* I/O Memory (size=64K) */
+ <0x01000000 0x00 0x00000000 0x00 0xefff0000 0x00 0x00010000>,
+ /* 32-bit MMIO (size=2G) */
+ <0x02000000 0x00 0x40000000 0x00 0x40000000 0x00 0x80000000>,
+ /* 64-bit MMIO (size= 124G) */
+ <0x03000000 0x01 0x00000000 0x01 0x00000000 0x7f 0x00000000>;
+ };
+};
--
1.9.3


\
 
 \ /
  Last update: 2014-11-24 23:21    [W:0.487 / U:0.564 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site